This is a
Inclusion and Exclusion are confirmed by a single click on the button. If the Aeon Labs Inline Smart Energy Illuminator is not included into any Z-Wave network, the LED will be blinking continually.
The Aeon Labs Inline Smart Energy Illuminator is a Z-Wave light dimmer specifically used to enable Z-Wave commands and control (on/off/dim) a device that is connected to a standard Schuko Wall Outlet.
It can also report immediate wattage consumption or kWh energy usage over a period of time. The wireless module is powered from the mains supply and is a three-wire design which requires a neutral connection. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.
The Aeon Labs Inline Smart Energy Illuminator can be plugged between every Standard-Schuko wall outlet and the electrical appliance with maximum load of 625W. To switch the plugged device on or off simply push the local button once or use a Z-Wave Controller. The status is shown by the status LED at the device.
The dimmer is operated by the local switch/button or wireless via Z-Wave. A single click switches the device on or off. To have the dimming function simple hold the button pushed until your desired level.
The Aeon Labs Inline Smart Energy Illuminator can report wattage energy usage or kWh energy usage to a Z-Wave gateway or controller when requested. If this function is supported by the gateway/controller, the energy consumption will be displayed in the user interface of the gateway/controller. Please consult the operation manual for these gateways/controllers for specific instructions.
Reset to factory default | XXXResetDescription |
Inclusion | To include the Aeon Labs Inline Smart Energy Illuminator with your Z-Wave controller simple bring it in the inclusion mode and click the Inclusion/Exclusion button at the Aeon Labs Inline Smart Energy Illuminator once. If the Aeon Labs Micro Inline Smart Energy Illuminator was successfully included to a Z-Wave network, the Status Indication LED will either be solid on or off (depending on if the switch is on or off) after the button was last pressed. |
Exclusion | To include the Aeon Labs Inline Smart Energy Illuminator with your Z-Wave controller simple bring it in the inclusion mode and click the Inclusion/Exclusion button at the Aeon Labs Inline Smart Energy Illuminator once. If the Aeon Labs Micro Inline Smart Energy Illuminator was successfully included to a Z-Wave network, the Status Indication LED will either be solid on or off (depending on if the switch is on or off) after the button was last pressed. |
NIF | A single click at the Inclusion/Exclusion switch sends a Node Information Frame. |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Status Reports |
Defines the value type to be sent as Sensor Report. Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Power |
01 | Voltage |
This is a double byte value. The LSB defines the total time the device need to blink. The value if set in seconds. The MSB defines the on/off interval of the blinking. The unit is 0.1 s. Size: 2 Byte, Default Value: 0000
Setting | Description |
---|
Defines the automated status notification of an associated device when status changes Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Deactivated |
01 | Hail sent |
02 | BASIC Report Sent |
Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Disabled |
01 | Enabled |
The value represents the minimum change in Wattage for a Report to be sent . Size: 2 Byte, Default Value: 0032
Setting | Description |
---|---|
00 - 3500 | Value in Watt |
The value represents the minimum change in Wattage Percent for a report to be sent Size: 1 Byte, Default Value: 0a
Setting | Description |
---|---|
00 - 100 | Percentage |
Defines the type of report sent for the Reporting Group 1. Size: 4 Byte, Default Value: 00000008
Setting | Description |
---|---|
Byte 1: 00000100 | MultiSensor Report |
Byte 1: 00001000 | Meter Report for Watt |
Byte 1: 00010000 | Meter Report for kWh |
Defines the type of report sent for the Reporting Group 2. Size: 4 Byte, Default Value: 00000000
Setting | Description |
---|---|
Byte 1: 00000100 | MultiSensor Report |
Byte 1: 00001000 | Meter Report for Watt |
Byte 1: 00010000 | Meter Report for kWh |
Defines the type of report sent for the Reporting Group 3. Size: 4 Byte, Default Value: 00000000
Setting | Description |
---|---|
Byte 1: 00000100 | MultiSensor Report |
Byte 1: 00001000 | Meter Report for Watt |
Byte 1: 00010000 | Meter Report for kWh |
Defines the time interval when the defined report of Reporting Group 1 is sent out. Size: 4 Byte, Default Value: 000002d0
Setting | Description |
---|---|
00 - ffff | Seconds |
Defines the time interval when the defined report of Reporting Group 2 is sent out. Size: 4 Byte, Default Value: 000002d0
Setting | Description |
---|---|
00 - ffff | Seconds |
Defines the time interval when the defined report of Reporting Group 3 is sent out. Size: 4 Byte, Default Value: 0000ffff
Setting | Description |
---|---|
00 - ffff | Seconds |
Dimensions | 0.0053000x0.0060000x0.0043000 mm |
Weight | 270 gr |
EAN | 1220000010499 |
Device Type | Light Dimmer Switch |
Generic Device Class | Multilevel Switch |
Specific Device Class | Routing Multilevel Switch |
Firmware Version | 01.18 |
Z-Wave Version | 02.4e |
Certification ID | ZC08-13030008 |
Z-Wave Product Id | 0086.0003.000d |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |