This is a
Inclusion and Exclusion are confirmed by a single click on the button. If the Aeon Labs Inline Smart Energy Switch is not included into any Z-Wave network, the LED will be blinking continually.
The Aeon Labs Inline Smart Energy Switch is a Z-Wave light switch specifically used to enable Z- Wave commands and control (on/off) a device that is connected to a standard Schuko Wall Outlet.
It can also report immediate wattage consumption or kWh energy usage over a period of time. The wireless module is powered from the mains supplys. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.
The Aeon Labs Inline Smart Energy Switch can be plugged between every Standard-Schuko wall outlet and the electrical appliance with maximum load of 3500W. To switch the plugged device on or off simply push the local button once or use a Z-Wave Controller. The status is shown by the status LED at the device.
The switch is operated by the local switch/button or wireless via Z-Wave. The click on the switch sets the switch on or off.
The Aeon Labs Inline Smart Energy Switch can report wattage energy usage or kWh energy usage to a Z-Wave gateway or controller when requested. If this function is supported by the gateway/controller, the energy consumption will be displayed in the user interface of the gateway/controller. Please consult the operation manual for these gateways/controllers for specific instructions.
Reset to factory default | XXXResetDescription |
Inclusion | To include the Aeon Labs Inline Smart Energy Switch with your Z-Wave controller simple bring it in the inclusion mode and click the Inclusion/Exclusion button at the Aeon Labs Inline Smart Energy Switch once. If the Aeon Labs Micro Inline Smart Energy Switch was successfully included to a Z-Wave network, the Status Indication LED will either be solid on or off (depending on if the switch is on or off) after the button was last pressed. |
Exclusion | To include the Aeon Labs Inline Smart Energy Switch with your Z-Wave controller simple bring it in the inclusion mode and click the Inclusion/Exclusion button at the Aeon Labs Inline Smart Energy Switch once. If the Aeon Labs Micro Inline Smart Energy Switch was successfully included to a Z-Wave network, the Status Indication LED will either be solid on or off (depending on if the switch is on or off) after the button was last pressed. |
NIF | A single click at the Inclusion/Exclusion switch sends a Node Information Frame. |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Status Reports |
Defines the value type to be sent as Sensor Report. Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Power |
01 | Voltage |
This is a double byte value. The LSB defines the total time the device need to blink. The value if set in seconds. The MSB defines the on/off interval of the blinking. The unit is 0.1 s. Size: 2 Byte, Default Value: 0000
Setting | Description |
---|
Defines the automated status notification of an associated device when status changes Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Deactivated |
01 | Hail sent |
02 | BASIC Report Sent |
Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Disabled |
01 | Enabled |
The value represents the minimum change in Wattage for a Report to be sent . Size: 2 Byte, Default Value: 0032
Setting | Description |
---|---|
00 - 3500 | Value in Watt |
The value represents the minimum change in Wattage Percent for a report to be sent Size: 1 Byte, Default Value: 0a
Setting | Description |
---|---|
00 - 100 | Percentage |
Defines the type of report sent for the Reporting Group 1. Size: 4 Byte, Default Value: 00000008
Setting | Description |
---|---|
Byte 1: 00000100 | MultiSensor Report |
Byte 1: 00001000 | Meter Report for Watt |
Byte 1: 00010000 | Meter Report for kWh |
Defines the type of report sent for the Reporting Group 2. Size: 4 Byte, Default Value: 00000000
Setting | Description |
---|---|
Byte 1: 00000100 | MultiSensor Report |
Byte 1: 00001000 | Meter Report for Watt |
Byte 1: 00010000 | Meter Report for kWh |
Defines the type of report sent for the Reporting Group 3. Size: 4 Byte, Default Value: 00000000
Setting | Description |
---|---|
Byte 1: 00000100 | MultiSensor Report |
Byte 1: 00001000 | Meter Report for Watt |
Byte 1: 00010000 | Meter Report for kWh |
Defines the time interval when the defined report of Reporting Group 1 is sent out. Size: 4 Byte, Default Value: 000002d0
Setting | Description |
---|---|
00 - ffff | Seconds |
Defines the time interval when the defined report of Reporting Group 2 is sent out. Size: 4 Byte, Default Value: 000002d0
Setting | Description |
---|---|
00 - ffff | Seconds |
Defines the time interval when the defined report of Reporting Group 3 is sent out. Size: 4 Byte, Default Value: 0000ffff
Setting | Description |
---|---|
00 - ffff | Seconds |
Dimensions | 0.0000000x0.0000000x0.0000000 mm |
EAN | 1220000011250 |
Device Type | On/Off Power Switch |
Generic Device Class | Binary Switch |
Specific Device Class | Binary Power Switch |
Firmware Version | 01.03 |
Z-Wave Version | 02.61 |
Certification ID | ZC08-13030009 |
Z-Wave Product Id | 0086.0003.0006 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |