Everspring
On/Off Mini Plug
SKU: AN180-6
Quickstart
This is a
1. Put the Z-Wave Controller into inclusion mode.2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode. (Please refer to the documentation for the location of the link key.)
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The On/Off Mini Plug is a Z-Wave enabled device which is fully compatible with any Z-Wave enabled network.Z-Wave enabled devices displaying the Z-Wave logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturers Z-Wave enabled networks.Inclusion of this unit on other manufacturers Wireless Controller menu allows remote operation of the unit and the connected load.The On/Off Mini Plug is designed to control the on/off status of lighting and appliances load in your house.At 220-240V voltage, this Plug can support up to 1500W resistive, 800W incandescent, 200W motor, or 200W fluorescent load.
| Reset to factory default | (This procedure should only be used when the network primary controller is inoperable.)1. Press the link key three times within 1.5 seconds to put the unit into exclusion mode.2. Within 1 second of step 1, press link key again and hold it until LED is off (about 5 seconds). (Please refer to the documentation for the location of the link key.)3. Node ID is excluded.The device reverts to factory default state and will be in auto-inclusion mode for 4 minutes. |
| Inclusion | 1. Put the Z-Wave Controller into inclusion mode.2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode. (Please refer to the documentation for the location of the link key.) |
| Exclusion | 1. Put the Z-Wave Controller into exclusion mode.2. Press the link key three times within 1.5 seconds to put the unit into exclusion mode. (Please refer to the documentation for the location of the link key.) |
| NIF | XXXNIF |
| Wakeup | NR |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | 1. When the unit is powered for the first time, the unit will send a Notification Report to the node of Group 1.2. When setting the unit or changing the units status, the unit will send a Binary Switch Report to the node of Group 1.3. Device Reset: When performing Reset the unit will send Device Reset Locally Notification to the node of Group1.4. The minimum interval time between two reports sent from this unit to the node of Group 1 is 3 seconds.Refer to Configuration parameter 2 for more information |
| 2 | 4 | When the button on the unit or the wall switch is pressed, the unit will send a Basic Set command to the nodes of Group 2.When the unit is OFF, Basic Set Value = 0x00.When the unit is ON, Basic Set Value = 0xFF. |
Configuration Parameters
Parameter 1: Basic Set Command value
Basic Set Command value Size: 2 Byte, Default Value: 255
| Setting | Description |
|---|
Parameter 2: The delaying time to report to Group 1
The delaying time to report to Group 1 Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|
Parameter 3: Remember the last status
1: Remember, 0: do not remember Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|
Technical Data
| Hardware Platform | SD3502 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | 02 |
| Z-Wave Version | 6.51.02 |
| Certification ID | ZC10-14080009 |
| Z-Wave Product Id | 0x0060.0x0004.0x0007 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |