This is a
Press and hold the SOS push button until the indicator light starts blinking. Then release the button to start the inclusion process.
(Note: Normally button should be pressed for 2 seconds but in case the product is already included it can take up to 12 seconds before the indicator light will start blinking.)
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Set Parameter 1 to value 255
The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
This device is battery operated and turned into deep sleep state most of the time to save battery life time. Communication with the device is limited. In order to communicate with the device, a static controller C is needed in the network. This controller will maintain a mailbox for the battery operated devices and store commands that can not be received during deep sleep state. Without such a controller, communication may become impossible and/or the battery life time is significantly decreased.
This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup Notification. The controller can then empty the mailbox. Therefore, the device needs to be configured with the desired wakeup interval and the node ID of the controller. If the device was included by a static controller this controller will usually perform all necessary configurations. The wakeup interval is a tradeoff between maximal battery life time and the desired responses of the device. To wakeup the device please perform the following action: Press and hold the Panic Watch for 14 seconds.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
|Group Number||Maximum Nodes||Description|
If configuration parameter 4 configured with value 0 then this group is used - SOS button: send ALARM_REPORT.
If configuration parameter 4 configured with value other then 0 (1-255) then this group is used - SOS button: send BASIC_SET, 0xFF.
|2||8||Not used on application.|
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Set all configuration values to default values (factory settings). Size: 1 Byte, Default Value: 0
|255||set to default|
The time that the panic pushbutton must be pressed before a (panic) message is sent out to the controller. Size: 1 Byte, Default Value: 1000
|0||Send directly the panic message when pressed|
|1 - 255||Send a panic message after you keep holding the button pressed for this value x 10ms.|
Minimum time that led feedback is shown after a panic message. Size: 1 Byte, Default Value: 100
|0||Led only stays on during the ‘send time’.|
|1 - 233||Led stays on during send time + this value*10ms.|
With this config parameter you can map the buttons to send different Z-Wave messages. Size: 1 Byte, Default Value: 255
|0||SOS button sends an ALARM_REPORT to nodes group 1|
|1 - 255||SOS button sends an BASIC_SET, 0xFF to nodes group 1|
|Dimensions||46 x 46 x 15 mm|
|IP Class||IP 21|
|Battery Type||1 * CR2450 3.0V|
|Device Type||Panic Button|
|Generic Device Class||Binary Sensor|
|Z-Wave Product Id||0x008a.0x0015.0x0101|
|Frequency||Europe - 868,4 Mhz|
|Maximum transmission power||5 mW|