This is a
Reset to factory default | 1. When the light is off, press and hold the push button for 2 seconds and then release to start the exclusion routine (indicator light start blinking 3 times per second).
2. Now to reset the device, press and release the push button 4 times within 1.5 seconds during the exclusion routine.
3. When ‘back to factory settings’ is done successfully, the indicator light is turned on for 1 second at the end of the exclusion routine. |
Inclusion | 1. Make sure a Z-Wave controller or the user interface is in the correct mode: ready for inclusion.
2. When the lamp and indicator light are off (!) press and hold the button. After circa 2 seconds, when the indicator light starts blinking, release the button to start the inclusion process.
3. When classic inclusion failed, the product will start Network Wide Inclusion automatically (max 20 seconds). |
Exclusion | 1. Make sure a Z-Wave controller or the user interface is in the correct mode: ready for exclusion.
2. When the lamp and indicator light are off (!) press and hold the button. After circa 2 seconds, when the indicator led starts blinking, release the button to start the exclusion process.
3. Make sure the Plug-in Dimmer is in direct range of the controller! |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 8 | All nodes in this group will receive a BASIC_SET frame when light is set to a certain state with the button of the Plug-in Dimmer (manual switching). |
2 | 1 | The node associated in this group will receive a unsolicited SWITCH_MULTILEVEL_REPORT frame every time the level of light is changed, where the value represents the (changed) dim level. The status is reported after every change that means manual but also if changed by Z-Wave. |
Set all config values to default values (factory settings). Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
255 | Default |
This parameter is used to enable the dimming option of the product. When disabled the dimming and fading routine are disabled. Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | Dimming disabled |
1 - 255 | Dimming enabled |
The maximum powerload when light is turned on, when measured higher then this value the Plugin Dimmer automatically stops with dimming or is turned off. Size: 2 Byte, Default Value: 125
Setting | Description |
---|---|
25 - 150 | Value in watts |
The speed of dimming when activated (manual and RF) Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | Dim speed is 1% per configuration value (* 10 ms) |
The speed of fading up when light is switched on (manual and RF) Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 255 | Fade speed is 1% per value (* 10 ms) |
A percentage that a energy value must be different compared to a previous sent value before a unsolicited meter report is sent. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 100 | A value in %. |
A watt value that a energy value must be different compared to a previous sent value before a unsolicited meter report is sent Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
5 - 150 | A value in watt. |
A time value that has to be passed compared to a previous sent value before a unsolicited meter report is sent Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
10 - 255 | A value in seconds |
What to do with lamp status when power applied Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Always switch light off when power applied |
1 | Switch lamp on/off depending on last known lampstatus before power was disconnected. |
The speed of fading down when activated (manual and RF) Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 255 | Fade speed is 1% per value (* 10 ms) |
Dimensions | 0.0000000x0.0000000x0.0000000 mm |
Weight | 54.57 gr |
Hardware Platform | ZM3102 |
EAN | 4008297483700 |
IP Class | IP IP 21 |
Voltage | 230 V |
Load | 125 W |
Device Type | Light Dimmer Switch |
Generic Device Class | Multilevel Switch |
Specific Device Class | Routing Multilevel Switch |
Firmware Version | 00.40 |
Z-Wave Version | 03.34 |
Z-Wave Product Id | 0x008a.0x0018.0x0100 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |