wiDom

WiDom Dimmer

SKU: B_WIDEWTD

Quickstart

This is a Z-Wave Device for Europe. To run this device please connect it to your mains power supply.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

With the WiDom Dimmer you get the possibility to integrate existing switchable and dimmable electric installations such as lighting or ceiling fans into your Z-Wave network. Thus, the connected load can be switched and dimmed via Z-Wave or with your existing toggle or momentary switch.

Make your lamps smart with the WiDom Dimmer. The following types of lamps can be controlled by the WiDom Dimmer:

Traditional incandescent and halogen bulbs
Dimmable energy-saving CLF fluorescent bulbs
Dimmable LED bulbs
Dimmable Low voltage bulbs with transformer

The compact radio module is placed in a wall box right behind the normal switch. The switch is no longer directly connected to the load but acts as an input device for the WiDom Dimmer that is controlling the load. The switch only sends control signal to the insert which controls the load. With your gateway you also can define different times when the lamps shall turn ON or OFF.

With the LED you get feedback directly if the electrical connections are correct. Thus the installation is much more easy. Furthermore the WiDom Dimmer acts as a repeater and increases the reliability of your Z-Wave network. Equipped with a very precise power metering funcionality as well as overheat protection mode it is ahead of competing products.

Features:

Flush-mounted trailing edge Z-Wave Dimmer
Integrates existing installations (lighting, ceiling fans) into the Z-Wave network
Suitable for different lamp types (halogen, LED, CLF fluorescent, etc.)
Works with every type of switch
Even with small loads, there will be no flickering
Power metering function
Overheat protection (turn off the load when the temperature exceeds a certain level)
Power supply: 110 - 230V, 50/60Hz
Power consumption: < 1W
Maximum load: 300W
Wireless technology: Z-Wave Plus
Dimensions: 37x37x17mm

We would like to point out that this article is not a new product. The product has got the complete functionality and can be integrated into a Z-Wave Smart Home without restriction. However, the product may have the following characteristics:

broken seal,
damaged packaging,
no original packaging,
missing accessories,
minimal signs of wear,
no current software version.

We offer to you a guarantee of one year. With a possible return you receive a credit note, there is no exchange of the product. The picture may not correspond to the scope of delivery of the product. If you are interested in a larger quantity of used products, please contact your sales representative.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions	0.0377200x0.0371300x0.0182300 mm
Weight	23.23 gr
Frequency	Europe - 868,4 Mhz
Maximum transmission power	5 mW

Explanation of Z-Wave specific terms

Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.