Quickstart

This is a Thermostat - HVAC for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
Press and hold the network button for 5 seconds.The thermostat must be in OFF mode.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

The Z-Wave Plus enabled CT110 is a sleek, modern thermostat design for home automation systems.Its clean user interface compliments app-enabled systems, and it connects to a Z-Wave network with one touch.The CT110 features adjustable real-time alerts to enable cloud triggers, a robust data stream of HVAC information for cloud monitoring, and configurable comfort response settings to customize home control scenes.The CT110 is compatible with all popular HVAC systems and is battery-operated without the need for a C-wire.

Reset to factory default	Press the network button 5 times to factory reset the thermostat (will clear the network information).The thermostat must be in OFF mode.Use the reset procedure only when the primary controller is missing or inoperable.
Inclusion	Press and hold the network button for 5 seconds.The thermostat must be in OFF mode.
Exclusion	Press and hold the network button for 5 seconds.The thermostat must be in OFF mode.
NIF	XXXNIF
Wakeup	When included into a Z-Wave network on battery power, this device is a FLiRS device.The Thermostat will wake up for communication when it receives a valid Z-Wave beam.
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	2	Z-Wave Plus Lifeline

Configuration Parameters

Parameter 1: Temperature Reporting Threshold

The Temperature Reporting Threshold Con!guration Set Command sets the reporting threshold for Reporting Threshold changes in the ambient temperature as detected by the thermostat.
Size: 1 Byte, Default Value: 2

Setting Description

Parameter 10: Temperature Reporting Filter

The Temperature Reporting Filter configuration command sets upper and lower bounds of the ambient temperature reporting.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 31868 Byte 1: 0 -124F (lower bound), Byte 2: 0-124F (upper bound)

Setting	Description
0 - 31868	Byte 1: 0 -124F (lower bound), Byte 2: 0-124F (upper bound)

Parameter 11: Simple UI Mode

Enables or disables Simple UI mode on thermostat via RadioBus Read/Set UI command.
Size: 1 Byte, Default Value: 1

Setting Description
0 - 1 0 = Normal Mode, 1 = Simple Mode

Setting	Description
0 - 1	0 = Normal Mode, 1 = Simple Mode

Parameter 12: Multicast

This parameter controls how the thermostat sends unsolicited reports.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 0 = Disabled, 1 = Enabled

Setting	Description
0 - 1	0 = Disabled, 1 = Enabled

Parameter 13: Main Display Settings

This Conifuration Param on the CT110 sets what information is displayed in the main thermostat display area (the largest central numbers on the display) .
Size: 1 Byte, Default Value: 1

Setting Description
1 - 2 1=temperature 2=humidity

Setting	Description
1 - 2	1=temperature 2=humidity

Parameter 14: Save Energy Mode Type

This configuration value is used to read/white what behavior Save Energy Mode causes in the thermostat when the thermostat enters Save Energy Mode.
Size: 1 Byte, Default Value: 3

Setting Description
1 - 255 1=Adjust by target delta, 2=Least consuming point in the running program, 3=Save energy absolute setpoint, 255=Save Energy not supported (read-only value)

Setting	Description
1 - 255	1=Adjust by target delta, 2=Least consuming point in the running program, 3=Save energy absolute setpoint, 255=Save Energy not supported (read-only value)

Parameter 2: HVAC Settings

The HVAC Settings Configuration Report Command returns the current HVAC con!guration. The HVAC settings must be !xed before the thermostat is joined to the Z-Wave network.
Size: 4 Byte, Default Value: 0

Setting Description
0 - 2147483647 Byte 1: normal (1) or heat pump (2). Byte 2, Bits 7-4: Gas (1) or Electric (2). Byte 2, Bits 3-0: # of Auxiliary Stages. Byte 3: # of Heat Pump Stages. Byte 4: # of Cool Stages.

Setting	Description
0 - 2147483647	Byte 1: normal (1) or heat pump (2). Byte 2, Bits 7-4: Gas (1) or Electric (2). Byte 2, Bits 3-0: # of Auxiliary Stages. Byte 3: # of Heat Pump Stages. Byte 4: # of Cool Stages.

Parameter 3: Utility Lock

The Utility Lock Con!guration Set command enables or disables the utility lock. If the utility lock is enabled, the setpoint cannot be modi!ed directly via the thermostat screen.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 255 0 = Disabled, 1 - 255 = Enabled

Setting	Description
0 - 255	0 = Disabled, 1 - 255 = Enabled

Parameter 4: C-Wire/Battery

The C-Wire / Battery Status Con!guration Report Command returns the status of the thermostat power source. The power state is fixed when the thermostat joins the network.
Size: 1 Byte, Default Value: 0

Setting Description
1 - 2 1=C-Wire, 2=Battery

Setting	Description
1 - 2	1=C-Wire, 2=Battery

Parameter 5: Humidity Reporting Threshold

The Humidity Threshold Con!guration Set Command sets the reporting threshold for changes in the relative humidity as detected by the thermostat.
Size: 1 Byte, Default Value: 5

Setting Description
0 - 3 0 = Disabled, 1 = 3% RH, 2 = 5% RH, 3 = 10% RH

Setting	Description
0 - 3	0 = Disabled, 1 = 3% RH, 2 = 5% RH, 3 = 10% RH

Parameter 6: Auxiliary/Emergency Mode

The Auxiliary/Emergency con!guration command enables or disables auxiliary / emergency heating in the thermostat.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 0 = Disabled, 1 = Enabled

Setting	Description
0 - 1	0 = Disabled, 1 = Enabled

Parameter 7: Thermostat Swing Temperature

The Thermostat Swing Temperature configuration command sets swing temperature on the Temperature thermostat.
Size: 1 Byte, Default Value: 2

Setting Description
1 - 8 1 = 0.5F, 2 = 1.0F, 3 = 1.5F, 4 = 2.0F, 5 = 2.5F, 6 = 3.0F, 7 = 3.5F, 8 = 4.0F

Setting	Description
1 - 8	1 = 0.5F, 2 = 1.0F, 3 = 1.5F, 4 = 2.0F, 5 = 2.5F, 6 = 3.0F, 7 = 3.5F, 8 = 4.0F

Parameter 8: Thermostat Differential Temperature

The Thermostat Differential Temperature configuration command sets the differential temperature for multi-stage HVAC systems.
Size: 2 Byte, Default Value: 4

Setting Description
2 - 6 The thermostat di#erential temperature is in units of 0.5 degrees Fahrenheit.

0 - 1 0x00 (Heat) or Cool (0x01)

Setting	Description
2 - 6	The thermostat di#erential temperature is in units of 0.5 degrees Fahrenheit.
0 - 1	0x00 (Heat) or Cool (0x01)

Parameter 9: Thermostat Recovery Mode

The Thermostat Recovery Mode configuration command sets the HVAC recovery mode type. The recovery mode determines when additional HVAC stages are turned of as the ambient temperature returns to the target temperature.
Size: 1 Byte, Default Value: 2

Setting Description
1 - 2 1 = Fast, 2 = Economy

Setting	Description
1 - 2	1 = Fast, 2 = Economy

Technical Data

Hardware Platform	ZM5202
Device Type	Thermostat - HVAC
Network Operation	Always On Slave
Firmware Version	02
Z-Wave Version	6.51.02
Certification ID	ZC10-15060005
Z-Wave Product Id	0x0098.0x6E01.0x0000
Frequency	XXfrequency
Maximum transmission power	XXantenna

Radio Thermostat Company of America

CT110

SKU: CT110