This is a
2. Pressing tamper key three times within 1.5 seconds to enter the inclusion mode.
3. After add successful, the LED will light ON 1 second
Siren MT02758 is a wireless siren, based on Z-Wave technology. It is the Z-Wave plus product, it support the security, OTA... Those newest features of the Z-Wave technology.
Use the Home Control alarm siren only indoors. Ceiling or wall mounting is possible.
The alarm function is switched off when the Home Control alarm siren is delivered. Once the device is added to the home control network, a disassembly alarm is automatically activated, which would be triggered for 3 minutes if the siren is removed from the housing mount. Mute the alarm in the web interface of the Home Control Portal before removing the alarm siren from the mounting plate.
The device generates a loud and shrill alarm sound that can damage the hearing. Maintain a minimum distance of about 50 cm.
Change Battery
The device use a Battery from type BL-5V 5V, 1200mA
Pay attention to the correct polarity when inserting the batteries. Incorrect use of the batteries can damage the device!
As soon as the device is added to the Home Control network, a disassembly alarm is automatically activated, which triggers for 3 minutes when the siren is removed from the housing mount. Mute the alarm in the web interface of the Home Control Portal before removing the alarm siren from the mounting plate.
Reset to factory default | 1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4 pressed, and the LED will light ON. 2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once. 3. IDs are excluded and all settings will reset to factory default. |
Inclusion | Pressing tamper key three times within 1.5 seconds to enter the inclusion mode. |
Exclusion | Pressing tamper key three times within 1.5 seconds to enter the exclusion mode. Node ID has been excluded. |
NIF | Press the tamper button |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | The Home Control alarm siren supports the Z-Wave® firmware update via OTA. When the firmware download is complete, the LED starts flashing every 0.5 seconds.
Do not disconnect the alarm siren from power during the update, the firmware may become defective and damage the device.
When the LED stops flashing, it is recommended to restart the unit (see below: manual switching off of the alarm siren). Caution: After switching off the unit, wait approx. 30 seconds until you reconnect the power supply unit. |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 8 | Z-Wave Plus Lifeline |
Customer function switch, using bit control Size: 1 Byte, Default Value: 8
Setting | Description |
---|---|
8 | Disable sound |
16 | Notification Type, 0: Using Notification Report. 1: Using Sensor Binary Report. |
Disable the alarm function. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Enable Alarm. |
1 | Disable Alarm, |
Play alarm sound duration, 1 tick is 30 seconds. Default is 3 minutes, maximum is 63.5 minutes Size: 1 Byte, Default Value: 6
Setting | Description |
---|---|
0 | Never auto stop |
1 - 127 | Play alarm sound duration, 1 tick is 30 seconds |
Dimensions | 110.000x19.000x110.000 mm |
Weight | 111 gr |
Hardware Platform | SD3502 |
EAN | 4250059696778 |
IP Class | IP 20 |
Battery Type | 1 * BL-5C |
Device Type | Siren |
Network Operation | Always On Slave |
Z-Wave Version | 6.51.09 |
Certification ID | ZC10-17035525 |
Z-Wave Product Id | 0x0175.0x0004.0x000A |
Color | White |
Supported Notification Types | Home Security |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |