Quickstart

This is a Notification Sensor for XXXQFrequencyName. To run this device please insert fresh 1 * CR123A batteries. To run this device please make sure the internal battery is fully charged. Put the Z-Wave Interface Controller into inclusion mode, and following its instruction to add the MT:2651 to your controller. To get in the inclusion mode, the distance between detector and controller is suggested to be in one meter. Press the program switch of MT:2651 for 1 second at least to be included. After setting, the LED Setting Lighting should go off, if not, please try again. (Please refer to the user manual to understand the program switch location)

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The Home Control Smoke Detector alarms you acoustically via an unmistakable signal sound, visually via an LED light and, if used with the devolo Home Control Central Unit, via text, e-mail or app. Thanks to the mobile and simultaneous notification sent to multiple mobile phone numbers and e-mail addresses that you select, you can respond immediately even when on the go. When combined with other Home Control devices, the Home Control Smoke Detector can, for example, additionally turn on the lights and open the shades via the Z-Wave® controller.

Installation

Power-On Mode

1. Turn the detector anti-clockwise to unscrew it from the housing backplate and access the battery compartment.

When screwing the Home Control Smoke Detector to the ceiling, make sure that no gas, water or power lines in the ceiling get damaged. There is a danger of electric shock!

2. Based on the drilling specifications on the housing backplate, drill holes into the room‘s ceiling at the desired location and attach the housing backplate using screws.

3. Now put the battery in the correct position (see marking in the battery compartment) in the Home Control Smoke Detector.

When you insert the battery, it pushes down the red locking pin without the use of force. This prevents the battery compartment from being closed without a battery inserted.

4. Close the battery compartment cover.

5. The installation was successful if the LED on the Home Control Smoke Detector flashes yellow once after about 10 seconds and you hear a short alarm tone.

Product Usage

Replacing the batteries

Do not use rechargeable batteries! The device uses a commercially available CR123 3V 1400mAh lithium battery.

Turn the detector anti-clockwise to unscrew it from the housing backplate and access the battery compartment.

1. Remove the old battery.

2. Now insert the new battery into the Home Control Smoke Detector in the correct position.

3. When inserting the battery, make sure the position is correct. Using the battery incorrectly can damage the device!

When you insert the battery, it pushes down the red locking pin without the use of force. This prevents the battery compartment from being closed without a battery inserted.

Function test

The battery change was successful if the LED on the Home Control Smoke Detector flashes yellow once after about 10 seconds and you hear a short alarm tone.

If the test alarm still does not provide acoustic or visual feedback, the device may be defective. For replacing the Home Control Smoke Detector, contact devolo AG.

Standby mode

The test alarm button with the red LED on the front side of the device serves to check the function. In addition, it makes the signal LED visible. Flashing of the red LED approximately every five minutes indicates that the smoke detector is ready. If smoke is detected, the red LED flashes fast and continuously, and simultaneously a triple beep sounds, which repeats again and again after short pauses.

Mute

The mute switch can temporarily suppress an alarm for up to 10 minutes.

To use this function, press the test alarm button on the front side of the device in case of an alarm. If there is still sufficient smoke concentration present after 10 minutes, the device will again set off the alarm.

Battery life warning

If the LED flashes, alternating between red and yellow, and if a short beep sounds every 43 seconds, the level of the battery of the Home Control Smoke Detector is low. When the warning about the battery level is activated, the battery will last for up to another 30 days, but for security reasons it should be replaced immediately after the warning.

Error message

If you hear a triple beep three times within 43 seconds and if the LED is flashing yellow, the smoke detector is not functioning properly. In this case, replace the device.

If the Home Control Smoke Detector is not functioning properly, contact devolo AG.

Activating the alarm

When smoke is detected, the Home Control Smoke Detector will send a message to the Z-Wave® controller.

Function test

1.Keep the test alarm button pressed until you hear the alarm tone and the LED flashes red.

2.To switch off the alarm again, simply release the test alarm button.

Reset to factory default	XXXResetDescription
Inclusion	Briefly press the test alarm button on the front of the smoke detector. The LED flashes red. With this, the registration on the Central Unit has been completed successfully.
Exclusion	Press the program switch of MT:2651 for 1 second at least to be excluded. The red LED setting light will flash continuously in Exclusion condition.
NIF	XXXNIF
Wakeup	Press program switch once, the detector will send NIF signal first and will also send Wake Up Notification after 3 seconds.
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	5	Z-Wave Plus Lifeline

Technical Data

Weight	136 gr
Hardware Platform	ZM5202
EAN	4250059698758
IP Class	IP 20
Battery Type	1 * CR123A
Device Type	Notification Sensor
Z-Wave Version	6.51.02
Certification ID	ZC10-14080006
Z-Wave Product Id	0x0175.0x2004.0x04a4
Frequency	Europe - 868,4 Mhz
Maximum transmission power	5 mW

Devolo

Smoke Detector