Quickstart

This is a secure HVAC-Thermostat for Europe. To run this device please insert fresh 2 * AA 1,5V batteries. Please make sure the internal battery is fully charged.

- Start Inclusion mode of your primary Z-Wave Controller.
- Press the Boost-Button.
- Spirit Z-Wave Plus will show the assigned NodeID.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Spirit Z-Wave Plus is a Z-Wave radio standard compatible energy-saving radiator thermostat.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Safety Warning for Batteries

The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.

Installation

Mounting the Spirit Z-Wave Plus

After adding the Spirit Z-Wave Plus to a network it is ready to be installed on the radiator. The LCD shows INS. Do not press the boost button yet.

Installation at the radiator without Adapter


Installation at the radiator with Adapter



Mechanical Installation

Press the boost button to start mechanical installation.



Unmounting the Spirit Z-Wave Plus





Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

Exclusion

Product Usage

Buttons:



Boost-Taste Led‘s




LCD



Inserting batteries

Remove the battery cover by simply pulling it off. Now insert the batteries. Pay attention to the correct
polarity! At a later battery change, the configuration of your Spirit Z-Wave Plus is maintained.





Setpoint adjustment

The setpoint is adjusted via plus and minus button.
Altering the setpoint locally will set the Spirit Z-Wave Plus in heating mode.
The energy saving setpoint can only be adjusted via Z-Wave.
The configurable setpoint range is 8°C to 28°C.
If the setpoint is increased/decreased above/below the set point limits the
Spirit Z-Wave Plus will change into boost / off ?mode.
 

 Child protection
 
Press and hold plus and minus button simultaneously for 3 seconds
to enable/disable the child protection.
If the Spirit Z-Wave Plus is set into the highest protection level it is no
longer possible to operate the device locally.
 
Altering the operating states

Off-Mode
Press minus button until OFF is displayed.

Boost-Mode
Push the boost button.
Alternatively press the plus button until ON is displayed.

Heating-Mode
If the operating state is not heating mode, pressing the plus or
minus button will bring the device in heating mode.

Window open detection
If the roomtemperature drops the window open detection will trigger.
Spirit Z-Wave Plus will change temporarily in off mode for 15 minutes.
Window open detection will end automatically after 15 minutes and the previously active
operating mode will be restored.
Window open detection can also be canceled by a button press.
The window open detection is disabled during manufacturer specific mode.
The sensitivity oft he window open detection can be configured

Display NodeID
Press and hold the boost button for 3 seconds to display the NodeID.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Group Number Maximum Nodes Description
1 1 Z-Wave Plus Lifeline

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Parameter 1: LCD invert

Inverts the LCD orientation
Size: 1 Byte, Default Value: 0

Setting Description
0 Normal orientation
1 LCD content inverted

Parameter 2: LCD Timeout

Configures the timeout of the LCD.
Size: 1 Byte, Default Value: 0

Setting Description
0 LCD always on
5 - 30 LCD timeout in seconds

Parameter 3: Backlight

Enables or disables the LCD-Backlight.
Size: 1 Byte, Default Value: 1

Setting Description
0 Backlight disabled
1 Backlight enabled

Parameter 4: Battery report

Enables or disables unsolicited battery reporting once a day.
Size: 1 Byte, Default Value: 1

Setting Description
0 Battery reporting disabled
1 Battery reporting enabled

Parameter 5: Measured temperature report

Reports the measured roomtemperature on change.
Size: 1 Byte, Default Value: 5

Setting Description
0 Reporting disabled
1 - 50 Reporting Delta in 1/10 Celcius

Parameter 6: Valve percentage report

Reports the valve percentage on change.
Size: 1 Byte, Default Value: 0

Setting Description
0 Reporting disabled
1 - 100 Reporting Delta in percent

Parameter 7: Window open detection

Configures the sensitivity of the window open detection.Sensitivity level: 1 low2 medium3 high
Size: 1 Byte, Default Value: 2

Setting Description
0 Detection disabled
1 - 3 Sensitivity level

Parameter 8: Measured temperature offset

Configures an offset for the measured temperature. Set the offset to -128 (0x80) if measured temperature is provided externally.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 50 Offset in 1/10 Celcius (0°C - 5°C)
128 Temperature is supplied externaly
206 - 255 Offset in 1/10 Celcius (-5°C - 0,1°C)

Technical Data

Dimensions 56x68x89 mm
Weight 127.64 gr
Hardware Platform ZM5202
EAN 4260012711301
IP Class IP 20
Voltage 3V
Battery Type 2 * AA 1,5V
Device Type Thermostat - HVAC
Network Operation Listening Sleeping Slave
Z-Wave Version 6.71.01
Certification ID ZC10-17095777
Z-Wave Product Id 0x0148.0x0003.0x0001
Supported Notification Types Power ManagementSystem
Thermostat HVAC Systems Supported Heat Only
Firmware Updatable Updatable by Consumer by RF
Thermostat Modes Energy Save HeatHeat
Sensors Air Temperature
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW

Supported Command Classes

  • Association Grp Info
  • Association V2
  • Basic
  • Battery
  • Configuration
  • Device Reset Locally
  • Firmware Update Md V3
  • Manufacturer Specific
  • Notification V8
  • Powerlevel
  • Protection
  • Security
  • Security 2
  • Sensor Multilevel V5
  • Supervision
  • Switch Multilevel
  • Thermostat Mode V3
  • Thermostat Setpoint V3
  • Transport Service V2
  • Version V2
  • Zwaveplus Info V2

Explanation of Z-Wave specific terms

  • Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
  • Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
  • Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
  • Inclusion — is the process of adding new Z-Wave devices into a network.
  • Exclusion — is the process of removing Z-Wave devices from the network.
  • Association — is a control relationship between a controlling device and a controlled device.
  • Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
  • Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.