Quickstart

This is a secure Siren for XXXQFrequencyName. To run this device please insert fresh 4 * LR14 batteries. To run this device please make sure the internal battery is fully charged.

The voice siren supports Auto Inclusion feature where it will automatically enter Inclusion mode when first powered up after a factory reset.
Note: Depending on country, the unit may be shipped with batteries already inserted. In this case, simply pull out the Battery Mylar, set the Z-Wave controller into Inclusion mode and then proceed to step 4.
1. Carefully remove its back cover by peeling from the opening slot at the bottom.
2. Set the Z-Wave controller into Inclusion mode.
3. Insert the battery into the battery compartment. Note the correct polarity of battery as indicated.
4. The unit’s LED will start to blink. The duration of Inclusion mode is 30 seconds.
5. The Inclusion process should be completed when the LED stops blinking.
Note: If you are connecting this unit to a Z-Wave Controller that utilizes the S2 security protocol, you may be asked by your controller to enter a 5-digit Device Specific Key (DSK) that is unique to each unit. This can be found in one of two places:
- on the QR code label on the back of the unit
- on the insert card inside the packaging.


Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The product is a voice alert and notification device. Prerecorded voice sounds can be stored into its memory and played back through gateway commands. For example, when email arrives, the audio sound youve got mail can be heard from its speaker. It also has a separate piezoelectric siren to emit a deafening sound when activated under emergency. In addition, the built in digital temperature sensor and humidity sensor reports environmental condition to the controller.

Installation

Inserting the batteries

1. Carefully remove its back cover by peeling from the opening slot at the bottom.
2. Insert the battery into the battery compartment. Note the correct polarity of battery as indicated.



Mounting the Unit
The voice siren should be mounted in a vertical position about 2 meters from the floor.

1. Use the backplate as a template to mark and drill the position of two mounting holes on the wall. Fix the backplate to the wall using the plastic wall plugs and fixing screws provided

2. Slide the unit down to its backplate and press against the wall to secure into place.

Product Usage

Product Overview



A. Voice Speaker
B. LED indicator
C. Siren
D. Temperature Sensor
E. Battery Mylar
F. Screw Mount
G. Backplate
H. Opening slot
I. Battery
J. Mini USB connector
K. Link button
L. Tamper switch
External Files:

For information on managing audio files on the siren, refer to the original manual included with the unit.

- Format : WAVE format (file extension .wav)
- Sample rate: 8KHz~32KHz.
- Mono only
- Maximum length : 30 seconds for each file

Note: MP3 file needs to be converted to .wav format.
  
1. Use a sound editor software on a PC to modify the audio files to fulfill the format above.
2. Save the files into a folder. Ensure the total size of all the files do not exceed 2MByte in size, which is roughly 85 seconds of playback.

Reset to factory default 1. Press the Link button 3 times within 1.5 seconds to put the unit into exclusion mode.
2. Within 1 second of step 1, press the Link button again and hold for 5 seconds.
3. Node ID is excluded. The unit reverts to factory default state.
Inclusion Press the Link button 3 times within 1.5 seconds to put the unit into inclusion mode.
Exclusion Press the Link button 3 times within 1.5 seconds to put the unit into exclusion mode.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Z-Wave Plus Lifeline

Configuration Parameters

Parameter 1: Siren alarm period

Siren alarm period
Size: 2 Byte, Default Value: 180

Setting Description
10 - 600 Siren alarm period can be set 10~600 seconds.

Parameter 2: Temperature/Humidity Auto Report period setting

Temperature/ Humidity Auto Report period setting
Size: 2 Byte, Default Value: 30

Setting Description
1 - 1440 Temperature/Humidity Auto Report period can be set 1~1440 minutes

Parameter 3: Sound Playback

Plays Sound
Size: 1 Byte, Default Value: 0

Setting Description
0 Stop to play sound
1 - 99 memory location number

Technical Data

Dimensions 0.0450000x0.2000000x0.0590000 mm
Weight 172 gr
Hardware Platform SD3502
EAN 4713616113588
IP Class IP 20
Voltage 6V
Battery Type 4 * LR14
Device Type Siren
Network Operation Listening Sleeping Slave
Z-Wave Version 6.71.03
Certification ID ZC10-18116293
Z-Wave Product Id 0x0060.0x000C.0x0003
Supported Notification Types Siren
Color White
Sensors Air Temperature
Firmware Updatable Updatable by Consumer by RF
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeSiren