Everspring
Z-Wave Power Meter Switch for Plug Typ E
SKU: EVR_AN1586
Quickstart
This is a
Inclusion and Exclusion are confirmed by a tripple click of the button of the device.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The AN1586 is a pluggable switch that controls electrical loads connected to mains power using standard Plug Typ E (France, Poland, ...) wall outlets. It can switch all electrical loads up to 3500 W and additionally measure the electrical power taken by this load (in Wh) and meters the electrical energy consumed (in kWh). The device is IP 20 rated and can only be used in dry environments. The device is operated either wirelessly using Z-Wave or with a button on the device. A red LED indicates the switching status.
Installation
The device can be plugged into every standard Schuko outlet (plug type E). Do not locate the Module facing direct sunlight, humid or dusty place. The suitable ambient temperature for the module is 0°C ~ 40°C.
Product Usage
Plug this module into a wall outlet near the load to be controlled. Plug the load into the module and switch the load to the ON position. To turn ON the module and the load plugged into it, press and release the ON/OFF button of the module.
The device is able to switch and measure any electric load up to 3500 W. Any load above 3000 W is considered as overloading. When overloading is detected the device will turn off the load, lock the local button and indicate the status by flashing the LED for 30 sec. Unplugging and replugging the module will reset the module to normal state. The electrical load can be switched using wireless commands and operating the local button. The LED inside the local button will indicate the switching status.
To access the metered and measure electric values a gateway with appropriate visualization is required.
| Reset to factory default | Tripple Click the button (same as for inclusion/exlusion) plus pushing the button again within 1 sec and hold it down for 5 sec. |
| Inclusion | Inclusion and Exclusion are confirmed by a tripple click of the button of the device. |
| Exclusion | Inclusion and Exclusion are confirmed by a tripple click of the button of the device. |
| NIF | Hit the button |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 2 | 4 | Pressing button to switch other devices |
| 1 | 1 | Send Alarm, Switch Report and Meter Report |
Configuration Parameters
Parameter 1: True Period
This is the time the switching status needs to remain unchanged after a change to cause the device to send out a status message Size: 1 Byte, Default Value: 0a
| Setting | Description |
|---|---|
| 00 | Disable |
| 01 - 78 | 10 * 100 ms = 1 sec |
Parameter 2: Send Out Basic Command
Enable or Disable the status message function when the local button press changes the switching state Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 | Disable |
| 01 | Enable |
Parameter 3: Meter Report Period
The device will report its meter value within the interval set. Set to 0 will disable the autoreporting function. Size: 2 Byte, Default Value: 0003
| Setting | Description |
|---|---|
| 0000 | Disabled |
| 0001 - 0ca8 | Interval = Wert * 10 sec |
Technical Data
| Dimensions | 0.0060000x0.0100000x0.0070000 mm |
| Weight | 150 gr |
| Device Type | On/Off Power Switch |
| Generic Device Class | Binary Switch |
| Specific Device Class | Binary Power Switch |
| Firmware Version | 01.01 |
| Z-Wave Version | 02.40 |
| Certification ID | ZC08-09100006 |
| Z-Wave Product Id | 0060.0004.0002 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |