Everspring
Z-Wave Presence Detector
SKU: EVR_HSP02
Quickstart
This is a
Tripple click the little button behind the battery cover to include or exclude the device. Clicking the little button behind the battery cover or a detected action by the sensor will wake up the device and keep it awake.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
This presence detector using PIR (passive infrared receiver) detects the presence of a person in a room. The unit sends information to a controller or any other associated Z-Wave device. Up to 5 devices can be controlled from this device. The sensor is a battery-powered device, which is in sleeping mode unless an action is detected. After a programmable sleeping time the device wakes up and sends a status information. After this the unit goes back to sleeping mode. The battery can be changed without unscrewing the device from the door or frame. The unit will give a visual warning on the device and sends a warning to the Z-Wave controller, when the battery needs to be replaced. The unit offers a tampering control and sends an alarm message when tampered.
Installation
1. Release the Sensor from the battery cover by removing the fixing screw.
2. Put the included CR2 battery in the battery compartment.
3. The recommended position for a PIR Detector is in the corner of a room mounted at a height between 1.8 and 2.0 m. At this height, the detector will have a maximum range of up to 9 m with a field of view of 110°. The monitoring range can be set up with PCB pattern.
4. The sensor can be mounted as follows:
(a) For mounting on a plane wall use the battery cover, which is also the mount plate, and the screws. Further fix the sensor with mount plate like shown in the picture.
(b) For mounting the sensor in a corner use the lateral holes of the mount plate. Further fix the sensor with mount plate like shown in the picture.
Product Usage
The Motion Detector is designed with two detecting sensors, Passive Infra-Red (PIR) sensor and light sensor, in order to fulfill the purpose of security and home automation. When the detector is cooperated with security appliances, it is acting as a security device by detecting changes in infra-red radiation levels. If a person moves within or across the device field of vision, a trigger radio signal will be transmitted to cause full alarm condition in order to frighten intruders away. Alternatively, when the detector is worked with home automation appliances, the detector can be set to perform the role of home automation device by detecting both changes in infra-red radiation levels and percentage of lux levels. Once night falls, the percentage of ambient illumination is lower than preset value. If a person moves within or across the device field of vision, a trigger radio signal will be transmitted e.g. to turn on the connected lightings for better illumination.
When the detector is first time powered up it is not included in a Z-Wave network and has no Associations. For Inclusion or setting an Association, the device has to be brought in the relevant mode and the inclusion/exclusion switch has to be clicked fast three times. The sensor supports two association groups, the first for one device (alarm) and the second for up to five devices (home automation).
| Reset to factory default | XXXResetDescription |
| Inclusion | Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Click the little button behind the battery cover fast three times to confirm the process. |
| Exclusion | Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Click the little button behind the battery cover fast three times to confirm the process. |
| NIF | Tripple click on the little button behind the battery cover or a detected action by the sensor sends a Node Information Frame. |
| Wakeup | Tripple click on the little button behind the battery cover or a detected action by the sensor will wake up the device and keep it awake. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Devices controlled by open/close events |
Technical Data
| Dimensions | 0.0620000x0.0900000x0.0410000 mm |
| Weight | 60 gr |
| Hardware Platform | ZM3102 |
| EAN | 4713616113236 |
| Battery Type | 2 * AAA |
| Device Type | Routing Binary Sensor |
| Generic Device Class | Binary Sensor |
| Specific Device Class | Routing Binary Sensor |
| Firmware Version | 01.03 |
| Z-Wave Version | 02.40 |
| Certification ID | ZC08-11120004 |
| Z-Wave Product Id | 0086.0002.0004 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |