Quickstart

This is a Z-Wave Device for XXXQFrequencyName. To run this device please insert fresh 1 * 9V Block batteries. To run this device please make sure the internal battery is fully charged.

 Inclusion, Exclusion and wakeup are confirmed by three times quickly hitting the binding button on the backside of the case.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The Smoke Detector SF812 uses a non-radioactive photo-sensor for a reliable and safe detection of smoke. Simply install the Smoke Detector on your ceiling and follow the procedure in the manual. Now your room is fitted with an early warning system against smoke. The smoke detector has a test button and a flashing led, so you always know that the smoke alarm is working correctly. The smoke alarm will warn you when the battery is low. When the device detects smoke, it will give a loud warning sound. It will also trigger actions in other Z-Wave devices or Z-Wave controllers to escalate the alarm. The Smoke Detector can also activate an alarm-scenario within the Z-Wave network. For example you can create an alarm-scenario to switch on all lights in the house when smoke is detected. Even at the middle of the night, you may leave the house very quickly when smoke is detected.

Installation

  1. Remove the mounting bracket from the detector by rotating it counterclockwise.
  2. Dissolve the upper case from the lower case by rotating it in the oppsite direction and loosen the connector.
  3. Open the battery cover and connect the battery in the correct position.
  4. Fix the mounting bracket at a wall or a ceiling with the two screws.
  5. Link the connector to the clip in the correct position and reassemble the upper case with the lower case.
  6. Fix the device to the mounting bracket by rotating it clockwise.

Please follow the recommendations about amount as position of the sensor in your home as given above. Avoid to place the sensor into the angle of walls, prefer positions in the middle of the room.

Product Usage

  • 1. The detector sounds as long as the test button is pressed for 3 seconds or there is smoke in the detector. When the detector goes off, always check carefully to see that there is no fire and never remove the battery from the detector except when changing it!
  • 2. Always test the detector immediately after returning from holiday, after a longer period of absence or periodically to ensure the detector funtions normally. Under the test button, there is a red control LED which flashes once every 30 seconds. It indicates the detector is under normal operation. When the Smoke Detector senses smoke and simultaneously sounds an audible alarm, the red LED will flash fast. If the detector does not sound when testing, the battery must be replaced.
  • 3. Never use an open flame to test your detector. You may set fire to damage the detector, as well as your home.

Reset to factory default XXXResetDescription
Inclusion

click the inclusion/exclusion switch quickly 3 times. The LED is on when the switch is pressed.

 

Exclusion

click the inclusion/exclusion switch quickly 3 times. The LED is on when the switch is pressed.

NIF

Hitting the inclusion/exclusion button three times will send out an Node Information Frame.

Wakeup

Tripple click on the inclusion/exclusion button will wake up the device and keep it awake for 5 seconds.

Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Devices to be informed about alarms

Technical Data

Dimensions 0.1020000x0.1020000x0.0500000 mm
Weight 180 gr
Hardware Platform ZM3102
Battery Type 1 * 9V Block
Firmware Version 01.04
Z-Wave Version 02.40
Certification ID ZC08-09070013
Z-Wave Product Id 0060.000d.0001
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeZ-Wave Device