Quickstart

This is a secure Window Control (endpoint aware) for Europe. To run this device please connect it to your mains power supply.

Inclusion and Exclusion are confirmed by a single click on the programming button. If the Fakro Chain Drive is not included into any Z-Wave network, the LED is on continually.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

The ZWS230 chain motor is thanks to its small dimensions and suitable force output ideal for roof window operating and is fully compatible with the Z-Wave system. The motor can be used to upgrade centre pivot and top hung and pivot roof windows of different manufacturers.

The maximum chain reach of the ZW230 is 36cm. The motor is equipped with built-in overload protection which acts as a sensor for correct window closing.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Installation

The Chain Drive for Pivot Windows (230V) is intended for operating centre pivot and top hung and pivot roof windows. The ZWS motors are equipped with a twoway "Z-Wave" communication radio module. ZWS motors are Security Enabled products. Security Enabled Z-Wave Controller must be used in order to fully utilize ZWS. The motor functionality is anyway identical when included as a secure and non-secure device.

The ZWS motors are equipped with two limits:

Install the ZWS motor with your roof window according installation manual.

Please read carefully the instructions below before proceeding to the device installation so as to prevent electric shock or injury. When installing the mechanical motor, it is necessary to observe the following recommendations:

WARNING!!! Danger of crashing. While closing, the motor exerts the force of 250N (app. 25kg).

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Click the programming button one time to confirm the process.

Exclusion

Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Click the programming button one time to confirm the process.

Product Usage

To be able to operate the ZWS230 motor by means with a Z-Wave controller it is necessary to:

There are different modes in which the device can be used:

"PROTECTION" - used to protect a device against unintentionally control by e.g. a child. Three levels can be set by any controller supporting this functionality.

Note: The description for activation and deactivation of the protection function is described in the user manual of the controllers supporting this function.

"RETURN ROUTE ASSIGNING" - depending on version actuator can be equipped with rain sensor input. In such case it is possible to link this actuator with other actuators which have not rain sensor functionality. In this case it is necessary to initiate "ASSIGN" function by Controller. Standard procedure which can vary for different controllers is:

Start "ASSIGN" function - press (1 sec) programming button on actuator without rain sensor - press (1 sec) programming button on actuator with rain sensor.

Note: For information on handling or initiation the assign function of products of another manufacturers, please read the documents of the respective manufacturer.

"All ON or All OFF" - it is possible to define if device should respect All close (OFF) or All Open (ON) command.

Note: The description for the "All ON or All OFF" function is described in the user manual of the devices supporting this function.

"SECURITY" ZWS motors are Security Enabled products. The security provides confidential communication between nodes in network.

Note: Security Enabled Z-Wave Controller must be used in order to fully utilize ZWS.

"MANUAL OPERATING" The "Manual operating" button makes it possible to operate the motor right after connecting the power supply. Manual operating works in sequential mode, i.e. start, stop, start in opposite direction, stop - etc.

Note: Watch the LED showing the status of devices on the network. Blinking LED indicates the status of protection state and may mean that the control of the device is not possible.

Node Information Frame

The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame. To issue a NIF execute the following action:

A sinlge click on programming button sends a Node Information Frame.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Group Number Maximum Nodes Description
1 5

Technical Data

Dimensions 0.0650000x0.0500000x0.3600000 mm
Weight 1130 gr
EAN 5900988500378
Device Type Window Covering Endpoint Aware
Generic Device Class Multilevel Switch
Specific Device Class Motor Control Device (B)
Firmware Version 03.0a
Z-Wave Version 02.61
Certification ID ZC08-11020009
Z-Wave Product Id 0085.0003.0001
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW

Supported Command Classes

Controlled Command Classes

Explanation of Z-Wave specific terms