This is a
Inclusion and Exclusion are confirmed by a single click on the programming button. If the Fakro Chain Drive is not included into any Z-Wave network, the LED is on continually.
The ZWS230 chain motor is thanks to its small dimensions and suitable force output ideal for roof window operating and is fully compatible with the Z-Wave system. The motor can be used to upgrade centre pivot and top hung and pivot roof windows of different manufacturers.
The maximum chain reach of the ZW230 is 36cm. The motor is equipped with built-in overload protection which acts as a sensor for correct window closing.
The Chain Drive for Pivot Windows (230V) is intended for operating centre pivot and top hung and pivot roof windows. The ZWS motors are equipped with a twoway "Z-Wave" communication radio module. ZWS motors are Security Enabled products. Security Enabled Z-Wave Controller must be used in order to fully utilize ZWS. The motor functionality is anyway identical when included as a secure and non-secure device.
The ZWS motors are equipped with two limits:
Install the ZWS motor with your roof window according installation manual.
Please read carefully the instructions below before proceeding to the device installation so as to prevent electric shock or injury. When installing the mechanical motor, it is necessary to observe the following recommendations:
WARNING!!! Danger of crashing. While closing, the motor exerts the force of 250N (app. 25kg).
To be able to operate the ZWS230 motor by means with a Z-Wave controller it is necessary to:
There are different modes in which the device can be used:
"PROTECTION" - used to protect a device against unintentionally control by e.g. a child. Three levels can be set by any controller supporting this functionality.
Note: The description for activation and deactivation of the protection function is described in the user manual of the controllers supporting this function.
"RETURN ROUTE ASSIGNING" - depending on version actuator can be equipped with rain sensor input. In such case it is possible to link this actuator with other actuators which have not rain sensor functionality. In this case it is necessary to initiate "ASSIGN" function by Controller. Standard procedure which can vary for different controllers is:
Start "ASSIGN" function - press (1 sec) programming button on actuator without rain sensor - press (1 sec) programming button on actuator with rain sensor.
Note: For information on handling or initiation the assign function of products of another manufacturers, please read the documents of the respective manufacturer.
"All ON or All OFF" - it is possible to define if device should respect All close (OFF) or All Open (ON) command.
Note: The description for the "All ON or All OFF" function is described in the user manual of the devices supporting this function.
"SECURITY" ZWS motors are Security Enabled products. The security provides confidential communication between nodes in network.
Note: Security Enabled Z-Wave Controller must be used in order to fully utilize ZWS.
"MANUAL OPERATING" The "Manual operating" button makes it possible to operate the motor right after connecting the power supply. Manual operating works in sequential mode, i.e. start, stop, start in opposite direction, stop - etc.
Note: Watch the LED showing the status of devices on the network. Blinking LED indicates the status of protection state and may mean that the control of the device is not possible.
Reset to factory default | XXXResetDescription |
Inclusion | Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Click the programming button one time to confirm the process. |
Exclusion | Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Click the programming button one time to confirm the process. |
NIF | A sinlge click on programming button sends a Node Information Frame. |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | Make sure that your Z-Wave Controller is in the Association-Mode. Click the programming button one time to confirm the process. |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 |
Dimensions | 0.0650000x0.0500000x0.3600000 mm |
Weight | 1130 gr |
EAN | 5900988500378 |
Device Type | Window Covering Endpoint Aware |
Generic Device Class | Multilevel Switch |
Specific Device Class | Motor Control Device (B) |
Firmware Version | 03.0a |
Z-Wave Version | 02.61 |
Certification ID | ZC08-11020009 |
Z-Wave Product Id | 0085.0003.0001 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |