Quickstart

This is a Multiposition Motor for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:

  1. Quickly, three times press switch no. 1 or the B-button



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

FIBARO Roller Shutter 2 is a module designed to control roller blinds, awnings, venetian blinds, gates and other single phase, AC powered devices. FIBARO Roller Shutter 2 allows precise positioning of roller blinds or venetian blind lamellas. The device is equipped with power and energy monitoring.

As with all other Actors, FIBARO Roller Shutter 2 allows to control connected devices either via the Z-Wave network or via a switch connected directly to it.

Installation


Connecting the device in a manner inconsistent with manual may cause risk to health, life or material damage.

When connecting the device act in accordance with the following rules:

  • Connect only in accordance with one of the diagrams
  • Do not connect DC powered motors, Roller Shutter 2 is dedicated to operate AC powered electric motors
  • Do not connect the device to loads exceeding recommended values
  • Electrical installation must be protected by overcurrent protection (fuse) of with a value not higher than 10A
  • The device should be installed in a wall switch box compliant with a relevant national safety standards and with depth no less than 60mm
  • Electrical switches used in installation should be compliant with the relevant safety standards
  • Length of wires used to connect the control switch should not exceed 20m

     

Venetian blind slats may be only operated by momentary switches.

Notes for the diagrams:

L – terminal for live lead
N – terminal for neutral lead  
S1 – terminal for switch no. 1 (has the option of entering the device in learning mode)
S2 – terminal for switch no. 2
Q1 – first output terminal for shutter motor 
Q2 – second output terminal for shutter motor
B – service button (used to add/remove the device)

Installation of the device:

  1. Switch off the mains voltage (disable the fuse)
  2. Open the wall switch box
  3. Connect with one of the diagrams below
  4. Verify correctness of connection
  5. Arrange the device and its antenna in a wall switch box
  6. Close the wall switch box
  7. Turn on the mains voltage
  8. Add the device to the Z-Wave network
  9. If necessary, calibrate the module

Switch connected to the S1 terminal operates the Q1 output, while the push button connected to the S2 terminal operates the Q2 output. It is recommended to connect an UP button to the S1 terminal and a wire, responsible of up movement, to the Q1 output terminal. Respectively, a DOWN button should be connected to the S2 terminal and a wire, responsible for down movement, to Q2 the output terminal.

    

Arranging the antenna

  • Locate the antenna as far from metal elements as possible (connecting wires, bracket rings, etc.) in order to prevent interferences.
  • Metal surfaces in the direct vicinity of the antenna (e.g. flush mounted metal boxes, metal door frames) may impair signal reception!
  • Do not cut or shorten the antenna – its length is perfectly matched to the band in which the system operates.

Product Usage

Manual operation

FIBARO Roller Shutter 2 allows for connecting push buttons to the S1 and S2 terminals. These may be momentary or toggle switches, alternatively. Push buttons are responsible for managing the blind’s movement.

Using momentary switches:

  • Clicking up button connected to the S1 terminal, initiates up movement.
  • Clicking down button connected to the S2 terminal, initiates down movement.

If the blind is moving, each click, of any button, will stop the movement. In addition a button click sends a command frame to 1st association group devices.

In case of venetian blinds it is possible to manage the slats angle. Operating Mode – Venetian Blind, or Parameter 10 value set to 2.

  • Holding up button connected to the S1 terminal initiates slats rotation up.
  • Holding down button connected to the S2 terminal initiates slats rotation down.

In addition a button hold sends a Fibar Command Class control frame to 2nd association group devices.

Using toggle switches:

  • Changing up button position connected to the S1 terminal, initiates up movement.
  • Changing down button position connected to the S2 terminal, initiates down movement.
  • Choosing a middle position stops the blind.

Menu

FIBARO Roller Shutter 2 has a MENU with each position indicated by the specified LED indicator colour.

In order to enter the menu press the B-button and hold for at least 2 seconds. While the B-button is still pressed, LED indicator colour will change in the following sequence:

  • BLUE – initiate the load calibration procedure
  • GREEN – reset the energy consumption data memory
  • VIOLET – initiate the Z-Wave network range test
  • YELLOW – reset the Roller Shutter 2 to factory defaults

Release the B-button to choose the desired function and confirm your choice with the B-button click.

Positioning calibration

 

Calibration is a process during which a Roller Shutter learns the position of the limit switches and a motor characteristic. Calibration is mandatory in order for the Roller Shutter to correctly recognize a roller blind position. The procedure consists of an automatic, full movement between the limit switches (up, down, and up again). There are separate procedures of calibrating roller blind and slats (venetian blind) positioning. Each time the calibration requires the completion of a full cycle (up and down).

To abort the calibration process press any button (connected to S1 or S2) or send a STOP control frame through the Z-Wave network controller. In Gate Controller mode the calibration process will be aborted after disconnecting the S2 terminal.
In Venatian Blind mode, slats need to be calibrated to work with any given motor.
Venetian blind slats may be only operated by momentary switches.

Positioning calibration

Calibration is a process during which a Roller Shutter learns the position of the limit switches and a motor characteristic. Calibration is mandatory in order for the Roller Shutter to correctly recognize a roller blind position. The procedure consists of an automatic, full movement between the limit switches (up, down, and up again). There are separate procedures of calibrating roller blind and slats (venetian blind) positioning. Each time the calibration requires the completion of a full cycle (up and down).

To abort the calibration process press any button (connected to S1 or S2) or send a STOP control frame through the Z-Wave network controller. In Gate Controller mode the calibration process will be aborted after disconnecting the S2 terminal.

In Venatian Blind mode, slats need to be calibrated to work with any given motor.

Venetian blind slats may be only operated by momentary switches.

Roller blind positioning calibration

There are 5 procedures of calibrating a Fibaro Roller Shutter to choose from. Each one gives the same results and the user may choose which one to execute.

Calibration through the FIBARO Home Center interface

  1. Make sure the module is supplied
  2. Add the device to the Z-Wave network
  3. Enter settings of the device by the clicking spanner icon
  4. Choose advanced settings tab
  5. Click the “Calibrate” button
  6. The device will perform the calibration process, completing full cycle – up, down and up again
  7. Test whether the positioning works correctly

Calibration through the Z-Wave network

  1. Make sure the module is supplied
  2. Add the device to the Z-Wave network
  3. Set the parameter 29 value to 1
  4. The device will perform the calibration process, completing full cycle – up, down and up again
  5. The parameter 29 value will be set to 0 automatically
  6. Test whether the positioning works correctly

Calibration through the switch keys

  1. Make sure the module is supplied and switch is connected to S1 and S2 terminals
  2. Add the device to the Z-Wave network
  3. Press and hold the button connected to S1 or S2 input terminal and release it after at least 3 seconds
  4. Press and hold the same button again, and release it after 3 seconds
  5. Now press and hold the same button, for 3 seconds, for the 3rd time
  6. After pressing and releasing the button for the third time, automatic calibration sequence will start
  7. The device will perform the calibration process, completing full cycle – up, down and up again
  8. Test whether the positioning works correctly

Calibration through the Menu (B-button)

  1. Make sure the module is supplied
  2. Add the device to the Z-Wave network
  3. Press and hold the B-button
  4. Wait for the visual indicator to glow yellow (4th MENU position)
  5. Release the B-button
  6. Press the B-button again, briefly
  7. The device will perform the calibration process, completing full cycle – up, down and up again
  8. Test whether the positioning works correctly

Calibration through a Fibar Command Class control frame

It is possible to force the calibration process execution through sending a Fibar Command Class control frame through a Z-Wave network main controller.

Slats positioning calibration in venetian blinds

Apart from calibrating the roller blind position, it is possible to calibrate the position of venetian blinds slats. After correct calibration, in case of venetian blinds, it is possible to set the position between the limit switches, as well as the slats angle. By default, time of full turn of the slats is set to 1.5 seconds. To modify settings

  1. Make sure the module is supplied
  2. Add the device to the Z-Wave network
  3. Calibrate the device normally
  4. Set the parameter 10 value to 2 or choose in the Home Center interface: Device Type – Venetian Blind
  5. Another device icon, responsible for slats operation, will show up in the Home Center interface.
  6. In case of any other Z-Wave network controllers managing the slats position is achieved through pressing and holding a switch key (up or down).
  7. By default, time of transition between extreme positions is set to 1 500 ms (1.5 seconds).
  8. Turn slats between extreme positions. If after full cycle a blind starts moving up or down, then parameter’s 12 value must be modified, e.g. to 1 000ms (1 second).
  9. Correctly configured slats should not force the blind to move up or down.

Operating gate motors

FIBARO Roller Shutter 2 allows to operate gate motors. Gate motor should be connected to Q1 and Q2 terminals according to installation diagram. In the Gate Mode, a momentary switch may be connected to S1 terminal. It is recommended to connect an IR barrier, an emergency stop button or any alarm mechanism to S2 terminal. Opening a contact in a device connected to S2 terminal will always result in stopping a motor in current position.

Clicking a push button connected to S1 terminal will initiate opening the gate. Next click of a button will stop the gate. Yet another click of a button will close the gate. According to following seaquence: OPEN → STOP → CLOSE → STOP → OPEN.

In Gate Mode, by default, the S1 terminal is set to operate with a momentary switch, ignoring the settings of parameter 14.

Full opening the gate initiates a Roller Shutter 2 COUNTDOWN. After the COUNTDOWN the gate will start closing. COUNTDOWN length is set through the parameter 12. In addition, if the IR barrier is cut (S2 contact opened) at the gate fully open, the gate will start closing after a time period specified in parameter 17.

In both Gate Modes, with and without positioning, parameters 12 and 17 are automatically set to 0. At these settings the gate will open, but will not automatically close. Relevant times need to be set manually in parameters 12 and 17.

Parameters 12 and 17 settings are automatically modified only in Home Center controller, when choosing one of Gate Modes. In case of controllers from other manufacturers these parameters need to be set manually.

Installation of the gate driver may be performed only by certified professionals. The motor must be equipped with the appropriate limit switches. It is recommended to connect a NC (normally closed) contact of an IR barrier to S2 terminal. Opening the contact will stop the gate. In addition, it’s recommened to connect an emergency stop button to the motors neutral (N) wire. In emergency, pushing the emergency stop button will cut the power and stop the gate. It is recomended to monitor regulary operation of FIBARO Roller Shutter 2 in all modes. Also it is recomended to regulary verificate and maintenance connectors.

S1 and S2 terminals react to mains voltage only. Using IR barriers with NC contacts operating on lower voltages require using an additional relay.

Reset to factory default
  1. Make sure the device is supplied
  2. Press and hold the B-button
  3. Wait for the visual indicator to glow yellow (4th MENU position)
  4. Release the B-button
  5. Press the B-button again, briefly
  6. After few seconds the device will be restarted with enabled auto-inclusion mode
  7. To exit auto-inclusion mode press the B-button
Inclusion
  1. Quickly, three times press switch no. 1 or the B-button
Exclusion
  1. Quickly, three times press switch no. 1 or the B-button
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 is assigned to the external switch – sending command frames to the associated devices whenever momentary switch is clicked or position of toggle switch is changed
2 5 is assigned to the external switch – sending command frames to the associated devices whenever momentary switch is hold
3 1 Lifeline reports the device status and allows to assign single device only (the main controller by default).

Configuration Parameters

Parameter 3: Reports type

Parameters value shoud be set to 1 if the module operates in Venetian Blind mode.
Size: 1 Byte, Default Value: 0

Setting Description
0 Blind position reports sent to the main controller using Z-Wave Command Class.
1 Blind position reports sent to the main controller using Fibar Command Class.

Parameter 10: Roller Shutter operating modes


Size: 1 Byte, Default Value: 1

Setting Description
0 Roller Blind Mode, without positioning
1 Roller Blind Mode, with positioning
2 Venetian Blind Mode, with positioning
3 Gate Mode, without positioning
4 Gate Mode, with positioning

Parameter 12: Venetian Blind Mode - time of full turn of the slats

In Gate Mode (parameter 10 set to 3 or 4) the parameter defines the COUNTDOWN time, i.e. the time period after which an open gate starts closing. In any other operating mode the parameter value is irrelevant.
Size: 2 Byte, Default Value: 150

Setting Description
0 gate will not close automatically
1 - 65535 (0.01-655.35s, 0.01 step)

Parameter 13: Set slats back to previous position

In Venetian Blind Mode (parameter 10 set to 2) the parameter influences slats positioning in various situations. In any other operating mode the parameter value is irrelevant.
Size: 1 Byte, Default Value: 1

Setting Description
0 Slats return to previously set position only in case of the main controller operation.
1 Slats return to previously set position in case of the main controller operation, momentary switch operation, or when the limit switch is reached.

Parameter 14: Switch type


Size: 1 Byte, Default Value: 0

Setting Description
0 momentary switches
1 toggle switches
2 single, momentary switch (the switch should be connected to S1 terminal)

Parameter 17: Roller Blind Mode and Venetian Blind Mode - turning off relays after reaching a limit switch

In Gate Mode (parameter 10 set to 3 or 4) the parameter determines a time period after which a gate will start closing after a S2 contact has been disconnected. In this mode, time to turn off the Roller Shutter relays after reaching a limit switch is set to 3 seconds and cannot be modified.
Size: 1 Byte, Default Value: 10

Setting Description
0 gate will not close automatically
1 - 255 (0.1-25.5s, 0.1 step)

Parameter 18: Motor operation detection

Power threshold to be interpreted as reaching a limit switch.
Size: 1 Byte, Default Value: 10

Setting Description
0 reaching a limit switch will not be detecte
1 - 255 (1-255W)

Parameter 22: Motor operation time

Time period for the motor to continue operation.
Size: 2 Byte, Default Value: 240

Setting Description
0 function is disabled
1 - 65535 (1-65535s)

Parameter 29: Forced Roller Shutter calibration

By modifying the parameters setting from 0 to 1 a Roller Shutter 2 enters the calibration mode. The parameter relevant only if a Roller Shutter is set to work in positioning mode (parameter 10 set to 1, 2 or 4).
Size: 1 Byte, Default Value: 0

Setting Description
1 start calibration process

Parameter 30: Response to General Alarm


Size: 1 Byte, Default Value: 2

Setting Description
0 no reaction
1 open blind
2 close blind

Parameter 31: Response to Flood Alarm


Size: 1 Byte, Default Value: 0

Setting Description
0 no reaction
1 open blind
2 close blind

Parameter 32: Response to Smoke, CO and CO2 Alarm


Size: 1 Byte, Default Value: 1

Setting Description
0 no reaction
1 open blind
2 close blind

Parameter 33: Response to Temperature Alarm


Size: 1 Byte, Default Value: 1

Setting Description
0 no reaction
1 open blind
2 close blind

Parameter 35: Managing slats in response to alarm.

In Venetian Blind Mode (parameter 10 set to 2), the parameter determines how the slats will react upon alarm detection. In any other modes, the parameter value is not relevant.
Size: 1 Byte, Default Value: 1

Setting Description
0 Do not change slats position – slats return to the last set position.
1 Set slats to their extreme position.

Parameter 40: Power level report

Power level change that will result in new power value report being sent. The parameter defines a change that needs to occur in order to trigger the report. The value is a percentage of the previous report.
Size: 1 Byte, Default Value: 10

Setting Description
0 reports are disabled
1 - 100 (100%)

Parameter 42: Periodic power or energy reports

This parameter determines a time period between consecutive reports.
Size: 2 Byte, Default Value: 3600

Setting Description
0 periodic reports are disabled
1 - 65534 (1-65534s)

Parameter 43: Energy reports

Energy level change which will result in new energy value report being sent. The parameter defines a change that needs to occur in order to trigger the report.
Size: 1 Byte, Default Value: 10

Setting Description
0 reports are disabled
1 - 254 (0.01-2.54kWh)

Parameter 44: Self-measurement

The device may include power and energy used by itself in reports sent to the main controller.
Size: 1 Byte, Default Value: 0

Setting Description
0 self-measurement inactive
1 self-measurement active

Parameter 50: Scenes/associations activation

Parameter determines whether scenes or associations are activated by the switch buttons.
Size: 1 Byte, Default Value: 0

Setting Description
0 associations activation
1 scenes activation

Technical Data

Dimensions 42x38x20 mm
Weight 28 gr
Hardware Platform ZM3102
EAN 5902020528340
IP Class IP 20
Voltage 230 V
Load 1,7 A
Device Type Roller Shutter
Generic Device Class Multilevel Switch
Specific Device Class Multiposition Motor
Network Operation Always On Slave
Z-Wave Version 4.52
Certification ID ZC08-11080006
Z-Wave Product Id 0x010F.0x0300.0x0102
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeRoller Shutter