FIBARO
Dimmer 2 250W Universal Insert Module
SKU: FIBRFGD-212
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
- Automatic Detection of a light source through advanced internal calibration
- Power Metering
- Compatible with 2 and 3 wire electrical systems
- Supports both leading and trailing edge
- Newest generation
- Powerful 500 Z-Wave Chip
- Z-Wave Plus protocol
- Built-in scene activation
- Security and Notification class
- Configuration menu with LED
- Complete DEKRA and Z-Wave Certification
- Maximum output of 250W
- New Intelligent Bypass 2*
Using the unique, specially designed algorithm, Dimmer 2 recognizes the type of a connected light source and calibrates itself to set proper values. Now you can be sure that lights in your home are controlled in the optimal way.
Compatible with both 2 and 3 wire systems
The Dimmer 2 is designed in such a way that it can be used in both 2 and 3 wire electrical systems, so you can use it in older electrical systems as well.
The new Dimmer 2 features power metering functionality.
You can view the energy consumption of your home in clear charts and graphs, and use it to reduce your energy consumption and monthly bills as well.
Control various light sources
The Dimmer 2 is an extremely advanced device, the first on the market to offer the possibility to control both the leading edge and the trailing edge. Now you are free to choose a light source and fully control it any way you want.
New options
Configure the lights as you wish with Dimmer 2 and the creative use of scenes. Imagine that in the middle of the night you need to go to the kitchen. You turn the lights on - and you&rsquore blinded. Sounds familiar? With Dimmer 2 the lights will turn on slightly dimmed, gently illuminating your way.
Scene management
Dimmer 2 offers an extremely intuitive scene management. The device will turn one of the light switch buttons into a scene trigger. Activating a selected scene becomes as simple as turning the light on. Just press the button while entering the room and all lights will be dimmed to the correct degree for a defined lightning atmosphere!
Intelligent notifications
The Dimmer 2 incorporates a number of security features protecting the device from overheating, overload and voltage drop. Should any of these security features happen, you will be notified immediately.
New intelligent Bypass 2
To increase the possibilities of the Dimmer 2 even more Fibaro has designed the new, microprocessor controlled Bypass 2.
More convenient connectors – Easy installation
The Dimmer 2 is equipped with large connecting terminals which simplify the installation process. You can connect it to wires of a larger diameter and make the installation faster.
User-friendly configuration menu
The built-in RGB diode is a perfect source of information during the installation process. It will show you when the Dimmer 2 has been included to or excluded from the network. You will see whether the calibration or software update has successfully completed. You can also check the Z-Wave network range.
Z-Wave range tester
Use the Dimmer 2 to test the Z-Wave network range. The built-in RGB diode will help you see if the place in which you chose to install the Dimmer 2 stays within the direct range of the Z-Wave network.
Software Update
You can update the software to its new version whenever available. This way you will always benefit from any new functionalities without the need of purchasing new device.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0430000x0.0430000x0.0630000 mm |
| Weight | 0.3 gr |
| Certification ID | ZC10-15090014 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.