Quickstart

This is a Z-Wave Device for XXXQFrequencyName. To run this device please insert fresh 1 * CR123 batteries. To run this device please make sure the internal battery is fully charged.

Inclusion, Exclusion and wakeup are confirmed by triple clicking the Z-Wave button inside the case.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The Fibaro Flood Sensor will alert you of a threatening flood or a rapid temperature rise or drop and has a wide variety of additional functions. Thanks to its flexible gold telescopic probes the device can even work on uneven surfaces. The Flood Sensor has a built in alarm siren which will help you to react quickly in case of a flood, rapid temperature change or the attempt to tamper with it. Aside from the alarm siren, the device can alert you of a threat using colour displays from the built in RGB diode. In addition to this a tilt sensor will detect tilt and movement over 15 degrees and send out a report to the main controller. The built in temperature sensor can not only be used to serve as a fire alarm sensor, it may also be used to manage an in-floor heating system.

The Input terminal allows you to connect an external probe and install the sensor in any location. The Output terminal allows for a connection to an alarm system. The Sensor will work on 12 or 24V DC or battery.

Installation

There are two powering modes for the Fibaro Flood Sensor, battery or mains current. By default it"s powered by a factory included battery. In addition it can work with a constant current, after connecting a 12 / 24V DC power supply to +12 and GND terminals. Powering mode configuration is carried out automatically, while a sensor is being included into the Z-Wave network. When battery powered, a Fibaro Flood Sensor communicates with a Z-Wave network main controller periodically. Detected alarms are sent immediately, but configuration parameters and associations settings only at specified wake up intervals, or at a manual wake up (button triple click). In DC powering mode, configuration and associations parameters are sent when necessary, and in addition a sensor serves as a Z-Wave signal repeater.

Switching to a constant current powering mode:

  • Exclude a sensor from the Z-Wave network.
  • Connect constant current power source (12 / 24 VDC) to +12 and GND terminals observing wiring (figure 1).
  • Include the Fibaro Flood Sensor into the Z-Wave network.

In constant powering mode a sensor may operate without a battery. Installing a battery is recommended though, as it will serve as an emergency power source. When constant power fails, sensor will automatically shift to an emergency mode. All reports, including flood and temperature, will be sent immediately, but it will not be possible to modify the configuration or association settings until constant power returns. If a sensor served as a signal repeater for other Z-Wave devices, in emergency mode signal repeating function will be deactivated.

Note: Fibaro Flood Sensor will automatically exit emergency mode once 12/24 VDC at +12 and GND terminals is detected and the device wakes up after detecting an event, i.e. flood alarm, temperature report, tilt, or manual wake up using button.

The Flood Sensor can also be used with an additional extended wire for the water sensor. Drill a hole into the casing and connect the wire as shown in figure 2.

Product Usage

Fibaro Flood Sensor has two sensors built in - flood and temperature sensors, meaning it"s a multichannel device. In the Z-Wave network"s main controller the Sensor will be shown as two devices.

Through an association Fibaro Flood Sensor may control another Z-Wave network device, e.g. a Dimmer, Relay Switch, Roller Shutter, RGBW Controller, Wall Plug, or a scene (scene only through the Home Center 2 main controller).

Fibaro Flood Sensor allows for the associations of three groups.

1-st Association Group is assigned to the device status - sending the BASIC SET (default) or ALARM control frame to the associated devices.

2-nd Association Group is assigned to a TMP button and tilt sensor - ALARM GENERIC control frame will be sent to the associated devices in case a TMP button is released or a tilt sensor triggered (depending on parameter 74 settings).

3-rd Association Group reports the device status and allows for assigning single device only (the main controller by default - the device reports its status to the main controller).

Fibaro Flood Sensor allows for controlling 5 regular and 5 multichannel devices per an association group, out of which 1 field is reserved for the Z-Wave network main controller.

Z-Wave Range Test

Fibaro Flood Sensor has a built in Z-Wave network range test for the main controller. Follow the instruction to test the main controller"s range:

  • Press and hold a TMP button for 10 - 15 seconds, until a LED indicator colour changes to violet.
  • Release the TMP button.
  • Click the TMP button again.
  • LED indicator will signal the Z-Wave network range (see description below).
  • To exit the Range Tester click the TMP button.

Z-Wave Range Tester signaling modes:

LED Indicator pulsing green - Fibaro Flood Sensor attempts to directly communicate with the main controller. If the direct communication attempt fails, the sensor will try routed communication, through other devices, which will be signaled with LED Indicator blinking yellow.

LED Indicator glowing green - Fibaro Flood Sensor directly communicating with the main controller.

LED Indicator pulsing yellow - Fibaro Flood Sensor tries to establish routed connection with the main controller, through intermediary devices.

LED Indicator glowing yellow - Fibaro Flood Sensor communicates with the main controller through other, intermediary devices. After two seconds the Sensor will retry to directly connect to the main controller, which will be signaled with the Indicator pulsing green.

LED Indicator pulsing violet - Fibaro Flood Sensor communicates at the range limit. If connection proves successful it will be confirmed with a yellow glow. It"s not recommended to use the sensor at the range limit.

LED Indicator glowing red - Fibaro Flood Sensor unable to connect to the main controller directly or through another Z-Wave network nodes.

Reset to factory default

Reset procedure deletes EPROM"s memory, including all information on the Z-Wave network and the main controller.

Fibaro Flood Sensor"s reset procedure:

1. Make sure the Sensor is powered.

2. Press and hold a TMP button for 15 - 20 seconds. LED indicator glows yellow to confirm entering 4th sub-menu.

3. Release the TMP button.

4. Click the TMP button, once.

5. The LED indicator glowing red and then turning off will confirm a successful reset. Reset completion will be confirmed by an acousic signal, same as at the power source connection.

Inclusion

Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Tripple click the Z-Wave button inside the case to confirm the process.

Exclusion

Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Tripple click the Z-Wave button inside the case to confirm the process.

NIF

Tripple click on the Z-Wave button inside the case or a detection by one of the sensors will send a Node Information Frame.

Wakeup

Tripple click on the Z-Wave button inside the case will wake up the device.

Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Flood Alarm with BASIC SET
2 5 Tilt Sensor alarm and TMP button events
3 1 reports device status

Configuration Parameters

Parameter 1: Alarm cancellation delay

Delays flood alarm cancelation for the device after flooding has ceased
Size: 2 Byte, Default Value: 0000

Setting Description

Parameter 2: Acoustic and visual signals On / Off in case of flooding

parameter allows for LED indicator and acoustic alarm deactivation in case of flooding detection
Size: 1 Byte, Default Value: 03

Setting Description
00 acoustic and visual alarms inactive
01 acoustic alarm inactive, visual alarm active
02 acoustic alarm active, visual alarm inactive
03 acoustic and visual alarms active

Parameter 5: Type of alarm frame sent to 1-st association group (FLOOD)

parameter determines a type of command frame sent by the Sensor in case flooding has been detected or cancelled
Size: 1 Byte, Default Value: 81

Setting Description
00 ALARM WATER command frame
81 BASIC SET command frame

Parameter 7: Forced dimming level sent to 1-st association group devices

Forced dimming level / roller blind opening level, when sending turn on / open
Size: 1 Byte, Default Value: 63

Setting Description

Parameter 9: Alarm cancelling or turning a device off (Basic) command frame deactivation

Allows for deactivating device turn off and alarm cancellation functions for the devices assigned to 1-st association group
Size: 1 Byte, Default Value: 00

Setting Description
00 Alarm (flooding) cancellation inactive
01 Alarm (flooding) cancellation active

Parameter 10: Temperature measurement interval

Time interval, in seconds, between consecutive temperature measurements
Size: 2 Byte, Default Value: 012c

Setting Description

Parameter 12: Temperature measurement hysteresis

Determines a minimum temperature change value (insensitivity level), resulting in a temperature report being sent
Size: 2 Byte, Default Value: 0032

Setting Description

Parameter 13: Alarm BROADCAST

Value other than 0 means alarms are sent in BROADCAST mode (with a priority over other communicates), to all devices within the Sensoru2019s range
Size: 1 Byte, Default Value: 00

Setting Description
00 broadcasts inactive
01 flood (1-st Association Group) broadcast active; tamper (2-nd Association Group) broadcast inactive
02 flood broadcast inactive; tamper broadcast active
03 flood broadcast active; tamper broadcast active

Parameter 50: Low temperature alarm threshold

parameter stores a temperature value, below which LED indicator blinks with a definable colour
Size: 2 Byte, Default Value: 05dc

Setting Description

Parameter 51: High temperature alarm threshold

parameter stores a temperature value, above which LED indicator blinks with a definable colour
Size: 2 Byte, Default Value: 0dac

Setting Description

Parameter 61: Low temperature alarm indicator LED colour

Parameter stores RGB colour value
Size: 4 Byte, Default Value: 000000ff

Setting Description

Parameter 62: High temperature alarm indicator LED colour

Parameter stores RGB colour value
Size: 4 Byte, Default Value: 00ff0000

Setting Description

Parameter 63: Managing a LED indicator under standard operation

Parameter determines LED indicatoru2019s operation. Set to 0 turns the indicator off, saving a battery life
Size: 1 Byte, Default Value: 02

Setting Description
00 LED indicator doesnu2019t indicate the temperature
01 LED indicator indicates the temperature (blink) every Temperature Measurement Interval (Parameter 10, constant current and battery) or Wake Up Interval (battery mode)
02 LED indicator indicates the temperature continuously, only in constant power mode

Parameter 73: Temperature measurement compensation

Parameter stores a temperature value to be added to or deducted from the current temperature measured to compensate temperature deflection
Size: 2 Byte, Default Value: 0000

Setting Description

Parameter 74: Alarm frame sent to 2-nd Association Group activation

parameter to device wich sensors send Alarm to 2. association group
Size: 1 Byte, Default Value: 02

Setting Description
00 tamper alarms inactive
01 button tamper alarm active
02 movement tamper alarm active
03 button and movement tampers alarm active

Parameter 75: Visual and audible alarms duration

parameter determines a time period after which visual and audible alarm will become u201cquietu201d
Size: 2 Byte, Default Value: 0000

Setting Description

Parameter 76: Alarm frame / Basic Set frame retransmission time when retaining flood alarm

Parameter determines a time period after which an alarm frame will be retransmitted
Size: 2 Byte, Default Value: 0000

Setting Description

Parameter 77: Flood sensor functionality turned off

Allows for turning off the internal flood sensor. Tamper and built in temperature sensor will remain active.
Size: 1 Byte, Default Value: 00

Setting Description
00 Default flood sensor operation (flood detection, reactions)
01 Built in flood sensor TURNED OFF (doesnu2019t change its state in the main controller, doesnu2019t send Alarms and Basic Set frames with flood state changes. Always visible in the main controller as turned off)

Technical Data

Dimensions 0.0650000x0.0650000x0.0280000 mm
Weight 41 gr
EAN 5902020528142
Battery Type 1 * CR123
Firmware Version 17.17
Z-Wave Version 03.34
Certification ID ZC08-14040015
Z-Wave Product Id 010f.0b00.1001
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeZ-Wave Device