Fibaro Group
Wall Plug with Metering Function Type E
SKU: FIB_FGWPE-101
Quickstart
This is a
The inclusion of the device is confirmed by a tripple click on the button. Additionally the device supports the autoinclusion function and will confirm inclusion when not manually included and plugged into an outlet. A red light on the LED ring confirms inclusion. The exclusion follows the same process but is recommended to use the Reset function to remove devices from the network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The Fibar plug with power metering function is a very compact stylish and intelligent remotely operable plug for wall outlets of Type E. It can be applied to switch loads up to 2500 W and will meter the acutal and accumulated power consumption of this load. A LED ring right on the device is used to indicate switching and power load stages or general alarm conditions, but can not be tuned up to all colors of the LED spectrum.
Installation
The plug can be plugged into every wall outlet for Plug-Type E. It is IP20 rated and can therefore only be used in dry environments. Do not locate the device facing direct sunlight, humid or dusty place. The suitable ambient temperature for the device is 0°C ~ 40°C. Plugs must not be stacked and operated.
Product Usage
The device is operared by the little button on the device or by wireless Z-Wave commands. The function of the LED ring can be defined using configuration parameters. It is possible to signal overcurrent or general alarm conditions of the Z-Wave network. In parallel the device indicates with purple light, when the ambient temperature exceeds 55 °C.
| Reset to factory default | To reset the plug and delete all settings, plug the device into the outlet and keep the button on the devices pushed for about 15...20 seconds until the LED ring starts to shine yellow. Now release the button and tip the button again shortly. The LED lights red to confirm the reset. |
| Inclusion | The inclusion of the device is confirmed by a tripple click on the button. Additionally the device supports the autoinclusion function and will confirm inclusion when not manually included and plugged into an outlet. A red light on the LED ring confirms inclusion. The exclusion follows the same process but is recommended to use the Reset function to remove devices from the network. |
| Exclusion | The inclusion of the device is confirmed by a tripple click on the button. Additionally the device supports the autoinclusion function and will confirm inclusion when not manually included and plugged into an outlet. A red light on the LED ring confirms inclusion. The exclusion follows the same process but is recommended to use the Reset function to remove devices from the network. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 3 | 1 | reports relais status to one device |
| 2 | 5 | send commands depending on current load |
| 1 | 5 | plug status. Will send BASIC command whenever the status of the plug changes |
Configuration Parameters
Parameter 1: Always On Function
Once activated, Wall Plug will keep a connected device constantly ON, will stop reacting to alarm frames and B-button push Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|---|
| 00 | active |
| 01 | inactive |
Parameter 16: Remember device status after power failure
Define how will the Plug react after the power supply is back on Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|---|
| 00 | Wall Plug does not memorize its state after a power failure. Connected device will be off after the power supply is reconnected |
| 01 | Wall Plug memorizes its state after a power failure |
Parameter 34: Reaction to Alarm
defines the alarm types the plug reacts to. Set value may be a sum of available values, e.g. set value = 5 means the Plug will respond to general alarm (1) and CO alarm (4). Size: 1 Byte, Default Value: 3f
| Setting | Description |
|---|
Parameter 35: Response to Alarm Frames
defines the response of the plug to an alarm. In always on mode this setting is ignored. Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 | No Reaction |
| 01 | Turn on connected device, LED ring signals alarm through time set in Parameter 39 or until alarm is turned off |
| 02 | Turn off connected device, LED ring signals alarm through time set in Parameter 39 or until alarm is turned off |
| 03 | Change Device state every second. In alarm mode the plug does not report status changes, power changes and ignores alarm frames. After alarm time (Parameter 39) has passed or alarm was canceled device is set back to previous state |
Parameter 39: Alarm duration
Wall Plugs alarm mode duration. If a device sending an alarm frame through the Z-Wave network sets alarm duration as well, this parameters settings are ignored. Size: 2 Byte, Default Value: 0258
| Setting | Description |
|---|
Parameter 40: Immediate Power Report
Parameter defines by how much power load must change, in percents, to be reported to the main controller, with the highest priority in the Z-Wave network. By default, Fibaro Wall Plug immediately sends power report if the power load changes by 80%. NOTE: In extreme cases, reports may be sent every second if rapid and significant power load changes occur. Frequent reporting may overload the Z-Wave network so these parameters settings should reflect significant changes in power load only. Size: 1 Byte, Default Value: 50
| Setting | Description |
|---|
Parameter 42: Standard Power Load Reporting
defines the change in power consumption to cause an unsolicided power report Size: 1 Byte, Default Value: 0f
| Setting | Description |
|---|
Parameter 43: Power Reporting Frequency
defines the frequency to send an unsolicided power report Size: 1 Byte, Default Value: 1e
| Setting | Description |
|---|---|
| 01 - fe | Define a frequency to send reports. |
| ff | Reports will be sent only as a result of parameter 47 settings or in case of polling |
Parameter 45: Reporting Changes in energy consumed by controlled devices
defines needed change of power draw to generate an unsoliceded power report Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 01 - fe | Define a value. Available settings: 1 - 254 (0,01kWh - 2,54kWh). |
| ff | Changes in consumed energy will not be reported. Reports will be sent only in case of polling. |
Parameter 47: Time Period between reports on power and energy consumption
defines the time pweriod between reports sent when changes in power load have nit been reported. Size: 2 Byte, Default Value: 0e10
| Setting | Description |
|---|---|
| 0001 - fffe | Define a time interval. |
| ffff | No periodic reports. Reports will be sent only in case of power load / energy consumption changes (parameters 40,42,43,45) or in case of polling. |
Parameter 49: Metering Energy consumed by Power Plug itself
defines whether or not the own power consumption shall be recorded. Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 | inactive |
| 01 | active |
Parameter 50: DOWN value
Lower power threshold, used in parameter 52 (value cannot be higher than a value specified in parameter 51) Size: 2 Byte, Default Value: 012c
| Setting | Description |
|---|
Parameter 51: UP value
Upper power threshold, used in parameter 52 (value cannot be lower than a value specified in parameter 50) Size: 2 Byte, Default Value: 01f4
| Setting | Description |
|---|
Parameter 52: Action in case of exceeding defined power values (Parameter 50/51)
definies the action for devices in association group 2 when power trigger value is reached. Size: 1 Byte, Default Value: 06
| Setting | Description |
|---|---|
| 00 | inactive |
| 01 | turns associated devices ON when when power drops below DOWN value |
| 02 | turns associated devices OFF when when power drops below DOWN value |
| 03 | turns associated devices ON when when power drops below UP value |
| 04 | turns associated devices OFF when when power drops below UP value |
| 05 | Option 1 and 4 combined |
| 06 | Option 2 and 3 combined |
Parameter 60: Power Load Trigger
defines the power load that will make the plug flash purple (only when parameter 61 is set to 0 or 1) Size: 2 Byte, Default Value: 61a8
| Setting | Description |
|---|
Parameter 61: LED Ring Color when device is on
defines the color of the LED ring in ON state Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|---|
| 00 | changes in predefined steps according to power load |
| 01 | changes continously according to power load using full spectrum of LED color |
| 02 | White |
| 03 | Red |
| 04 | Green |
| 05 | Blue |
| 06 | Yellow |
| 07 | Cyan |
| 08 | Magenta |
| 09 | Off |
Parameter 62: LED Ring Color when device is off
defines the color of the LED ring in OFF state Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|---|
| 00 | LED ring is illuminated with a color corresponding to the last measured power, before the controlled device was turned off |
| 01 | White |
| 02 | Red |
| 03 | Green |
| 04 | Blue |
| 05 | Yellow |
| 06 | Cyan |
| 07 | Magenta |
| 08 | Off |
Parameter 63: LED Ring Color on Z-Wave Alarms
defines the color of the LED ring on Alarm State Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|---|
| 00 | No Change of color |
| 01 | flashes red/blue/white |
| 02 | White |
| 03 | Red |
| 04 | Green |
| 05 | Blue |
| 06 | Yellow |
| 07 | Cyan |
| 08 | Magenta |
| 09 | Off |
Parameter 70: Overload Safety Switch
Allows turning off a device in case of overloading. This will even happen in always on mode. Device can be turned back on using the button on the device or sending a ON command. Size: 2 Byte, Default Value: ffff
| Setting | Description |
|---|
Technical Data
| Dimensions | 0.0430000x0.0430000x0.0650000 mm |
| Weight | 55 gr |
| EAN | 5902020528128 |
| Device Type | On/Off Power Switch |
| Generic Device Class | Binary Switch |
| Specific Device Class | Binary Power Switch |
| Firmware Version | 16.16 |
| Z-Wave Version | 03.34 |
| Certification ID | ZC08-14020004 |
| Z-Wave Product Id | 010f.0600.1000 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |