Quickstart

This is a On/Off Power Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. Auto-inclusion procedure, first set main controller into inclusion mode and then connect module to power supply. 
NOTE: When connecting temperature sensor to module that has already been included, you have to exclude module first. Switch off power supply , connect the sensor and re-include the module.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Qubino Flush 1D relay with voltage free (dry contact) output contact.
This Z-Wave module is used for switching on or off the electrical device (e.g. light, fan, etc ...). The module can be controlled either through Z-wave network or through the wall switch.
The module is designed to be mounted inside a “flush mounting box”, hidden behind a traditional wall switch.
Module supports connection of digital temperature sensor. It is designed to act as repeater in order to improve range and stability of Z-wave network.

Output contact is voltage free (dry contact), so also loads with different power supply can be connected to the module.

Installation

• To prevent electrical shock and/or equipment damage, disconnect electrical power at the main fuse or circuit breaker before installation or any servicing.
• Make sure, that no voltage is present in the installation.
• Prevent the disconnecting device from being switched on accidentally.
• Connect the module according to electrical diagram.
• Locate the antenna far from metal elements (as far as possible).
• Do not shorten the antenna.



Product Usage

Reset to factory default If the service button S is pressed for mor ethan 6 seconds the module will be reset to the factory defoult state
Inclusion • Press service button S for more than 2 second or press push button I1 three times within 3s (3 times change switch state within 3 seconds).
Exclusion • Press service button S for more than 6 second or press push button I1 five times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply. 
Note: By this function all parameters of the module are set to default values and own ID is deleted. If service button S is pressed more than 2 and less than 6second module is excluded, but configuration parameters are not set to default values
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Lifeline group (reserved for communication with the main controller).
2 16 basic on/off (triggered at change of the output state and reflecting its state) nodes.
3 16 basic on/off (triggered at change of the input I2 state and reflecting its state).
4 16 Binary Sensor Report (triggered at change of the input I2 state and reflecting its state).
5 16 Notification Report (triggered at change of the input I2 state and reflecting its state).

Configuration Parameters

Parameter 1: Input 1 switch type

Defines the type of switch connected to Input 1
Size: 1 Byte, Default Value: 1

Setting Description
0 mono-stable switch type (push button)
1 bi-stable switch type

Parameter 2: Input 2 contact type

Defines the type of switch connected to Input 2
Size: 1 Byte, Default Value: 0

Setting Description
0 NO (normally open) input type
1 NC (normally close) input type

Parameter 3: Input 3 contact type

Defines the type of switch connected to Input 3
Size: 1 Byte, Default Value: 0

Setting Description
0 NO (normally open) input type
1 NC (normally close) input type

Parameter 10: Activate / deactivate functions ALL ON/ALL OFF

Support to activate / deactivate functions ALL ON/ALL OFFFlush 1D relay module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.
Size: 2 Byte, Default Value: 255

Setting Description
255 ALL ON active, ALL OFF active
0 ALL ON is not active ALL OFF is not active
1 ALL ON is not active ALL OFF active
2 ALL ON active ALL OFF is not active

Parameter 11: Automatic turning off output after set time

Support automatic turning off output after set time.When relay is ON it goes automatically OFF after time defined by this parameter. Timer is reset to zero each time the module receive ON command regardless from where it comes (push button, associated module, controller,..).
Size: 2 Byte, Default Value: 0

Setting Description
0 Auto OFF disabled
1 - 32535 1 - 32535 = 1second (0,01s) - 32535 seconds (325,35s) Auto OFF enabled with define time, step is 1s or 10ms according to parameter nr.15

Parameter 12: Automatic turning on output after set time

Support automatic turning on output after set time When relay is OFF it goes automatically ON after time defined by this parameter. Timer is reset to zero each time the module receive OFF command regardless from where it comes (push button, associated module, controller,..).
Size: 2 Byte, Default Value: 0

Setting Description
0 Auto ON disabled
1 - 32535 1 - 32535 = 1second (0,01s) - 32536 seconds (325,35s) Auto ON enabled with define time, step is 1s or 10ms according to parameter nr.15

Parameter 15: Automatic turning off / on seconds or milliseconds selection

Support automatic turning off / on seconds or milliseconds selectionNOTE: This parameter is valid for both, turning on and turning off parameters.
Size: 1 Byte, Default Value: 0

Setting Description
0 seconds selected
1 milliseconds selected

Parameter 30: Saving the state of the relay after a power failure

Support saving the state of the relay after a power failure
Size: 1 Byte, Default Value: 0

Setting Description
0 Flush 1D relay module saves its state before power failure (it returns to the last position saved before a power failure)
1 Flush 1D relay module does not save the state after a power failure, it returns to "off" position.

Parameter 40: Power reporting in Watts on power change for Q1

Set value means percentage, set value from 0 - 100 = 0% - 100%.
Size: 1 Byte, Default Value: 10

Setting Description
0 Reporting Disabled
1 - 100 1% - 100% Reporting enabled. Power report is send (push) only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%. NOTE: if power changed is less than 1W, the report is not send (pushed), independent of percentage set.

Parameter 42: Power reporting in Watts by time interval for Q1

Set value means time interval (0 - 32535) in seconds, when power report is send.
Size: 2 Byte, Default Value: 300

Setting Description
0 Reporting Disabled
1 - 32535 = 1 second - 32535 seconds. Reporting enabled, Power report is send with time interval set by entered value.

Parameter 63: Output Switch selection

Support output Switch selectionSet value means the type of the device that is connected to the output. The device type can be normally open (NO) or normally close (NC).
Size: 1 Byte, Default Value: 0

Setting Description
0 When system is turned off the output is 0V (NC).
1 When system is turned off the output is 230V or 24V (NO).

Parameter 100: Enable / Disable Endpoint I2 or select Notification Type and Event

Support Enable / Disable Endpoint I2 or select Notification Type and EventEnabling I2, means that Endpoint (I2) will be present on UI. Disabling it will result in hiding the endpoint according to the parameter set value. Additionally, a Notification Type and Event can be selected for the endpoint. NOTE: After parameter change module has to be reincluded into the network for the setting to take effect!
Size: 1 Byte, Default Value: 1

Setting Description
1 Home Security; Motion Detection, unknown location
2 Carbon Monoxide; Carbon Monoxide detected, unknown location.
3 Carbon Dioxide; Carbon Dioxide detected, unknown location.
4 Water Alarm; Water Leak detected, unknown location.
5 Heat Alarm; Overheat detected, unknown location.
6 Smoke Alarm; Smoke detected, unknown location.
0 Endpoint, I2 disabled

Parameter 101: Enable / Disable Endpoint I3 or select Notification Type and Event

Support Enable / Disable Endpoint I3 or select Notification Type and EventEnabling I3, means that Endpoint (I3) will be present on UI. Disabling it will result in hiding the endpoint according to the parameter set value. Additionally, a Notification Type and Event can be selected for the endpoint. NOTE: After parameter change module has to be reincluded into the network for the setting to take effect!
Size: 1 Byte, Default Value: 1

Setting Description
1 Home Security; Motion Detection, unknown location
2 Carbon Monoxide; Carbon Monoxide detected, unknown location.
3 Carbon Dioxide; Carbon Dioxide detected, unknown location.
4 Water Alarm; Water Leak detected, unknown location.
5 Heat Alarm; Overheat detected, unknown location.
6 Smoke Alarm; Smoke detected, unknown location.
0 Endpoint, I3 disabled

Parameter 110: Temperature sensor offset settings

Defines temperature sensor offset settingsSet value is added or subtracted to actual measured value by sensor.
Size: 2 Byte, Default Value: 32536

Setting Description
32536 offset is 0.0C
1 - 100 value from 0.1C to 10.0C is added to actual measured temperature.
1001 - 1100 value from -0.1C to -10.0C is subtracted to actual measured temperature.

Parameter 120: Digital temperature sensor reporting

Defines the digital temperature sensor reportingIf digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter.
Size: 1 Byte, Default Value: 5

Setting Description
0 Reporting disabled
1 - 127 0,1C - 12,7C, step is 0,1C

Technical Data

Dimensions 0.0150000x0.0370000x0.0420000 mm
Weight 28 gr
Hardware Platform ZM5202
EAN 3830062070102
IP Class IP 20
Voltage 230 V
Load 2300 W
Device Type On/Off Power Switch
Network Operation Always On Slave
Z-Wave Version 6.51.06
Certification ID ZC10-15070017
Z-Wave Product Id 0x0159.0x0002.0x0053
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeOn/Off Power Switch