Qubino

Flush Dimmer

SKU: GOAEZMNHDD1

Quickstart

This is a secure Light Dimmer for Europe. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:

Press push button I1 three times within 3s (3 times change switch state within 3 seconds) or

Press service button S (only applicable for 24 V SELV supply voltage) for more than 2 second.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

This Z-Wave module is used for dimming the bulb or to manage the speed of a fan. The module can be controlled either through a Z-Wave network or through the wall switch. The module is designed to be mounted inside a â€œflush mounting boxâ€, hidden behind a traditional wall switch. Module measures power consumption of bulb or fan and supports connection of digital temperature sensor. It is designed to act as repeater in order to improve range and stability of Z-wave network.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Press push button I1 five times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or
Press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Installation

Electrical diagram 230VAC

Notes for the diagram:

N Neutral lead

L Live lead

~ Output for electrical device

I3 Input for switch/push button or sensor

I2 Input for switch/push button or sensor

I1 Input for push button/switch

TS Terminal for digital temperature sensor (only for Flush Dimmer module compatible digital temperature sensor, which must be ordered separately).

Electrical diagram 24VDC

Notes for the diagram:

N + VDC

L - VDC

~ Output for electrical device

I3 Input for switch/push button or sensor

I2 Input for switch/push button or sensor

I1 Input for push button/switch

TS Terminal for digital temperature sensor (only for Flush Dimmer module compatible digital temperature sensor, which must be ordered separately).

S Service button (used to add or remove module from the Z-Wave network in case of 24 V SELV power supply).

WARNING: Service button S must NOT be used when module is connected to 110-230V power supply.
NOTE: When overload is detected, module automatically switches off the output. In this case check if the load is according to specifications and if connections are according diagram. To recover module in normal state, you need to power cycle the module.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

Press push button I1 three times within 3s (3 times change switch state within 3 seconds) or

Press service button S (only applicable for 24 V SELV supply voltage) for more than 2 second.

Exclusion

Auto-Inclusion

Beside the standard inclusion this devices supports the so called auto inclusion. Right after powering up the device remains in inclusion state and can be included by (any) gateway without further actions on the device itself. The auto inclusion mode will time out after some time.

Product Usage

Bulb types which support dimming function:

· The classical incandescent bulbs.

· Halogen bulbs operated by 230 V AC (High Voltage Halogen).

· Low voltage halogen bulbs with electronic or conventional transformer.

· Dimmable compact fluorescent bulb (CFL). If the bulb at low intensities flushes, it is recommended to set parameter 60 (minimum dimming value) to 30 or more.

· Dimmable LED bulbs.

Description of switch function:

Switch toggles (parameter 1 set to 1) the state of the light bulb between the last dimming value and 0. If last dimming value is 0 then the light is turned 100% when switch changes its state.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Group Number	Maximum Nodes	Description
1	1
2	16
3	16
4	16
5	16
6	16
7	16
8	16
9	16
10	16
11	16

Technical Data

Dimensions	0.0330000x0.0380000x0.0160000 mm
Weight	22.99 gr
Hardware Platform	ZM5202
EAN	3830062070096
IP Class	IP 20
Voltage	230 V /24 V
Load	0,6A /0,85A
Device Type	Light Dimmer Switch
Generic Device Class	Multilevel Switch
Specific Device Class	Routing Multilevel Switch
Network Operation	Always On Slave
Firmware Version	03.05
Z-Wave Version	04.05
Certification ID	ZC10-16115319
Z-Wave Product Id	0159.0001.0051
Electric Load Type	Dimmable LEDIncandescentElectronic with/without Dimming
Color	Light Blue
Supported Meter Type	Electric Energy
Sensors	Temperature
Switch Type	Push Button
Frequency	Europe - 868,4 Mhz
Maximum transmission power	5 mW

Supported Command Classes

Basic

Switch Binary

Switch Multilevel

Switch All

Meter

Association Grp Info

Device Reset Locally

Zwaveplus Info

Configuration

Alarm

Manufacturer Specific

Powerlevel

Association

Version

Multi Channel Association

Security

Controlled Command Classes

Basic

Switch Multilevel

Explanation of Z-Wave specific terms

Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.