Quickstart
This is a
secure
Routing Multilevel Switch for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
Press push button I1 three times within 3s (3 times change switch state within 3 seconds) or
Press service button S (only applicable for 24 V SELV supply voltage) for more than 2 second.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Product Description
This Z-Wave module is used for dimming the bulb or to manage the speed of a fan. The module can be controlled either through a Z-Wave network or through the wall switch. The module is designed to be mounted inside a “flush mounting boxâ€, hidden behind a traditional wall switch. Module measures power consumption of bulb or fan and supports connection of digital temperature sensor. It is designed to act as repeater in order to improve range and stability of Z-wave network.
Installation
Electrical diagram 230VAC
Notes for the diagram:
N Neutral lead
L Live lead
~ Output for electrical device
I3 Input for switch/push button or sensor
I2 Input for switch/push button or sensor
I1 Input for push button/switch
TS Terminal for digital temperature sensor (only for Flush Dimmer module compatible digital temperature sensor, which must be ordered separately).
Electrical diagram 24VDC
Notes for the diagram:
N + VDC
L - VDC
~ Output for electrical device
I3 Input for switch/push button or sensor
I2 Input for switch/push button or sensor
I1 Input for push button/switch
TS Terminal for digital temperature sensor (only for Flush Dimmer module compatible digital temperature sensor, which must be ordered separately).
S Service button (used to add or remove module from the Z-Wave network in case of 24 V SELV power supply).
WARNING: Service button S must NOT be used when module is connected to 110-230V power supply.
NOTE: When overload is detected, module automatically switches off the output. In this case check if the load is according to specifications and if connections are according diagram. To recover module in normal state, you need to power cycle the module.
Product Usage
Bulb types which support dimming function:
· The classical incandescent bulbs.
· Halogen bulbs operated by 230 V AC (High Voltage Halogen).
· Low voltage halogen bulbs with electronic or conventional transformer.
· Dimmable compact fluorescent bulb (CFL). If the bulb at low intensities flushes, it is recommended to set parameter 60 (minimum dimming value) to 30 or more.
· Dimmable LED bulbs.
Description of switch function:
Switch toggles (parameter 1 set to 1) the state of the light bulb between the last dimming value and 0. If last dimming value is 0 then the light is turned 100% when switch changes its state.
Reset to factory default |
Press push button I1 five times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or Press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second. |
Inclusion |
Press push button I1 three times within 3s (3 times change switch state within 3 seconds) or
Press service button S (only applicable for 24 V SELV supply voltage) for more than 2 second. |
Exclusion |
Press push button I1 five times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or Press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second. |
NIF |
XXXNIF |
Wakeup |
XXXWakeupDescription |
Protection |
XXXProtection |
FirmwareUpdate |
XXXFirmwareUpdate |
SetAssociation |
XXXSetAssociation |
Association Groups:
Group Number |
Maximum Nodes |
Description |
1 |
1 |
|
2 |
16 |
|
3 |
16 |
|
4 |
16 |
|
5 |
16 |
|
6 |
16 |
|
7 |
16 |
|
8 |
16 |
|
9 |
16 |
|
10 |
16 |
|
11 |
16 |
|
Technical Data
Dimensions |
0.0330000x0.0380000x0.0160000 mm |
Weight |
22.99 gr |
Hardware Platform |
ZM5202 |
EAN |
3830062070096 |
IP Class |
IP 20 |
Voltage |
230 V /24 V |
Load |
0,6A /0,85A |
Device Type |
Light Dimmer Switch |
Generic Device Class |
Multilevel Switch |
Specific Device Class |
Routing Multilevel Switch |
Network Operation |
Always On Slave |
Firmware Version |
03.05 |
Z-Wave Version |
04.05 |
Certification ID |
ZC10-16115319 |
Z-Wave Product Id |
0159.0001.0051 |
Electric Load Type |
Dimmable LEDIncandescentElectronic with/without Dimming |
Color |
Light Blue |
Supported Meter Type |
Electric Energy |
Sensors |
Temperature |
Switch Type |
Push Button |
Frequency |
Europe - 868,4 Mhz |
Maximum transmission power |
5 mW |