This is a
This Z-Wave module is used for dimming the bulb or to manage the speed of a fan. The module can be controlled either through a Z-Wave network or through the wall switch. The module is designed to be mounted inside an electrical cabinet onto DIN rail. Module measures power consumption of bulb or fan and supports connection of digital temperature sensor. It is designed to act as repeater in order to improve range and stability of Z-wave network.
|
Do not connect the module to loads exceeding recommended values. Connect the module only in accordance to the below diagrams. Improper connections may be dangerous.
Description of switch function:
Switch toggles (parameter 1 set to 1) the state of the light bulb between the last dimming value and 0. If last dimming value is 0 then the light is turned 100% when switch changes its state.
Bulb types which support dimming function:
Reset to factory default |
|
Inclusion |
|
Exclusion |
|
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Lifeline |
2 | 16 | basic on/off |
3 | 16 | start level change/stop level change |
4 | 16 | multilevel set |
5 | 16 | multilevel sensor report (temperature sensor) |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | mono-stable switch type (push button) |
1 | bi-stable switch type |
With this parameter is possible to change the module presentation on the user interface.
NOTE: After parameter change, first exclude module (without setting parameters to default value) then wait at least 30s and then re include the module!
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Dimmer mode |
1 | Switch mode |
Size: 2 Byte, Default Value: 255
Setting | Description |
---|---|
255 | ALL ON active, ALL OFF active. |
0 | ALL ON is not active, ALL OFF is not active |
1 | ALL ON is not active, ALL OFF active |
2 | ALL ON active, ALL OFF is not active DIN Dimmer module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system. |
Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Auto OFF disabled |
1 - 32536 | 1 second - 32536 seconds Auto OFF enabled with define time, step is 1 second. |
Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Auto ON disabled |
1 - 32535 | 1 second - 32535 seconds Auto ON enabled with define time, step is 1 second |
If Double click function is enabled, a fast double click on the push button will set dimming power at maximum dimming value. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | double click disabled |
1 | double click enabled |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | DIN Dimmer module saves its state before power failure (it returns to the last position saved before a power failure). |
1 | DIN Dimmer module does not save the state after a power failure, it returns to off position. |
Set value means percentage, set value from 0 - 100=0% - 100%.
NOTE: if power changed is less than 1W, the report is not send (pushed), independent of percentage set.
Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
0 | reporting disabled |
1 - 100 | 1% - 100% Reporting enabled. Power report is send (push) only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%. |
Set value means time interval (0 – 32767) in seconds, when power report is send. Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | reporting disabled |
1 - 32767 | 1 second - 32767 seconds. Reporting enabled. Power report is send with time interval set by entered value. Please note, that too fast reporting can cause too much Z-Wave traffic resulting in Z-Wave poor response |
NOTE: The minimum level may not be higher than the maximum level! 1% min. dimming value is defined by Z-Wave multilevel device class Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 98 | 1% - 98%, step is 1%. Minimum dimming values is set by entered value. |
NOTE: The maximum level may not be lower than the minimum level! 99% max. dimming value is defined by Z-Wave multilevel device class. Size: 1 Byte, Default Value: 99
Setting | Description |
---|---|
2 - 99 | 2% - 99%, step is 1%. Maximum dimming values is set by entered value. |
Set value means time of moving the DIN Dimmer between min. and max. dimming values by short press of push button I or controlled through UI (BasicSet). Size: 2 Byte, Default Value: 100
Setting | Description |
---|---|
50 - 255 | 500 mseconds - 2550 mseconds (2,55s), step is 10 mseconds |
Time of moving the DIN Dimmer between min. and max dimming values by continues hold of push button I or associated device. Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | 1 second - 255 seconds |
This parameter is used with association group 3. A receiving device SHOULD respect the start level if the Ignore Start Level bit is 0. A receiving device MUST ignore the start level if the Ignore Start Level bit is 1.
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | respect start level |
1 | ignore start level |
This parameter is used with association group 3. The Duration field MUST specify the time that the transition should take from the current value to the new target value. A supporting device SHOULD respect the specified Duration value.
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | dimming duration according to parameter 66 |
1 - 127 | from 1 to 127 seconds |
Set value is added or subtracted to actual measured value by sensor. Size: 2 Byte, Default Value: 32536
Setting | Description |
---|---|
1 - 100 | value from 0.1 °C to 10.0 °C is added to actual measured temperature. |
1001 - 1100 | value from -0.1 °C to -10.0 °C is subtracted to actual measured temperature. |
If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter. Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
0 | reporting disabled |
1 - 127 | 0,1°C - 12,7°C, step is 0,1°C |
Dimensions | 0.0600000x0.0940000x0.0180000 mm |
Weight | 51.55 gr |
Hardware Platform | ZM5202 |
EAN | 3830062070386 |
IP Class | IP IP 20 |
Voltage | 230 V |
Load | 200 W |
Device Type | DIN Dimmer |
Generic Device Class | Multilevel Switch |
Specific Device Class | Routing Multilevel Switch |
Firmware Version | 01.01 |
Z-Wave Version | 04.05 |
Certification ID | ZC10-17035480 |
Z-Wave Product Id | 0x0159.0x0001.0x0052 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |