This is a
Heatit Z-Wave is an electronic thermostat for mounting in a standard wall box. The thermostat has a built-in Z-Wave chip that can be connected to Home Automation systems like Fibaro, Sensio, Vera, Zipato and others.
The display will show the actual room temperature. By pressing the buttons, the display will show the set value. Heatit Z-Wave is equipped with a single-pole switch.
The thermostat can handle loads up to 16A/3600Watt 230V. If the load is greater than this, the thermostat needs to be connected to a contactor. It can be used with two external temperature sensors.
Use e.g. a small slotted screwdriver. Start by carefully removing the front cover by pushing the release springs. The front cover and the frame can now be removed.
PROGRAMMING YOUR THERMOSTAT
To activate the programming mode, press Center (confirm) for 10 seconds. Now the display will show OFF. Now you are in programming mode. To scroll up and down in the menu use button 1 and 3 (left and right) to navigate. To enter submenu press Center (confirm). Always confirm your setting by pressing Center (confirm) for 2 seconds.
Reset to factory default | By pressing buttons Left and Center (up and confirm) for 20 seconds, the thermostat will perform a complete factory reset. |
Inclusion | Press Center (confirm) for 10 seconds. The display will show OFF. Press Right (down) 4 times till you see Con in the display. Now start add device in your home automation software. Start inclusion mode by pressing Center (confirm) for approximately 2 seconds. The inclusion/exclusion icon will appear in the display. Confirmation will show Inc/EcL in the display. If inclusion fails, Err (error) will appear. |
Exclusion | Press Center (confirm) for 10 seconds. The display will show OFF. Press Right (down) 4 times till you see Con in the display. Now start add device in your home automation software. Start inclusion mode by pressing Center (confirm) for approximately 2 seconds. The inclusion/exclusion icon will appear in the display. Confirmation will show Inc/EcL in the display. If inclusion fails, Err (error) will appear.. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | Use Update Cable for update. |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 8 | Z-Wave Plus Lifeline |
Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Off |
1 | Heat |
2 | Cool |
3 | Energy Save Heat |
Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | F-Mode |
1 | A-Mode |
2 | AF-Mode |
3 | A2-Mode |
4 | P-Mode |
5 | FP-Mode |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | 10K NTC |
1 | 12K NTC |
2 | 15K NTC |
3 | 22K NTC |
4 | 33K NTC |
5 | 47K NTC |
Size: 2 Byte, Default Value: 5
Setting | Description |
---|---|
3 - 30 | 0,3°C - 3°C |
Size: 2 Byte, Default Value: 50
Setting | Description |
---|---|
50 - 400 | 5°C - 40°C |
Size: 2 Byte, Default Value: 400
Setting | Description |
---|---|
50 - 400 | 5°C - 40°C |
Size: 2 Byte, Default Value: 50
Setting | Description |
---|---|
50 - 400 | 5°C - 40°C |
Size: 2 Byte, Default Value: 400
Setting | Description |
---|---|
50 - 400 | 5°C - 40°C |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 9 | Value |
Size: 2 Byte, Default Value: 210
Setting | Description |
---|---|
50 - 400 | 5°C - 40°C |
Size: 2 Byte, Default Value: 180
Setting | Description |
---|---|
50 - 400 | 5°C - 40°C |
Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 - 10 | Value |
Size: 2 Byte, Default Value: 210
Setting | Description |
---|---|
50 - 400 | 5°C - 40°C |
Dimensions | 85x85x50 mm |
Weight | 109 gr |
Hardware Platform | ZM5202 |
EAN | 7071236011934 |
IP Class | IP 20 |
Voltage | 230 V |
Load | 16A |
Device Type | Thermostat - HVAC |
Network Operation | Always On Slave |
Z-Wave Version | 6.51.00 |
Certification ID | ZC10-15020003 |
Z-Wave Product Id | 0x019B.0x0001.0x0001 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |