This is a
- If Inclusion Process is successful, Green LED will turn off.
The smart carbon monoxide sensor detects CO, and sends alarm signals to alert people of the danger.When the smart carbon monoxidesensor detects CO, it will send an alarm notification to the gateway through wireless Z-Wave communication protocol, then the gateway sends the notification to server, the server interprets the signal and transfers the signal to users‘ APP. The smart carbon monoxide sensor has high stability and sensitivity,which will protect house from CO poisoning effectively.
To increase safety factors in single-layer house, suggest to install at least a sensor in each bedroom and install a sensor at 6m from chimney and gas fixture.
To increase safety factors in multi-layer house, suggests to install at least a sensor in each bedroom, install at least one sensor in basement. Please install a sensor at 6m from chimney and gas fixture.
Anticlockwise rotating the bracket out from the installation base, then remove the battery insuating strip to make detector on power.
Screw the sensor into bracket, please remove the double - sided adhesive membrane on the installation base, and stick on the wall.
Inclusion / Exclusion / Reset
Battery Report
- Battery Report is transmitted when power on the device.
- Battery Report is transmitted once a day.
- Battery Report is transmitted when the battery falls less than 10%
Battery Voltage
|
Battery Level
|
2.6V ~ 3.0V
|
10 ~ 100 (%)
|
Under 2,6V
|
0xFF
|
Indicate LED statues description
Status
|
LED status
|
Alarm sound
|
Preheat
|
Green LED, red LED, yellow LED flash alternately
|
No sound
|
Normal
|
Green LED flash 1 time every 53 seconds
|
No sound
|
Test mode
|
Green LED, red LED, yellow LED and green LED flash alternately
|
?Di-Di-Di-Di?sound loudly
|
Alarm
|
Red LED flash 4 times every 10 seconds
|
?Di-Di-Di-Di?sound loudly
|
Low battery
|
Yellow LED flash 1 time every 53 seconds
|
?Di? sound every 53 seconds
|
Fault
|
Yellow LED flash 2 times every 10 seconds
|
?Di? sound twice every 10 seconds
|
|
Turn right to dismantle the mounting base of the device |
|
1)take out battery from the device 2)Insert the battery into the device ( You must be careful of the battery polarity) |
|
Turn left to install the mounting base of the device (before install the mounting base, you should must insert battery firstly, otherwise the mounting base will not be fixed) |
Reset to factory default | - Long press Network Button while installing batteries in HS1CA-Z. - Device Reset Locally notification is Transmitted. |
Inclusion | - Press the Network Button 3 times within 1.5s, the green LED is Blinking 3 times within 1 second. - If Inclusion Process is successful, Green LED will turn off. |
Exclusion | - Press the Network Button 3 times within 1.5s - If Exclusion Process is successful, Green LED is Blinking 6 times, then turn off. |
NIF | XXXNIF |
Wakeup | - Wake up Notification is transmitted every 24 hours by default. - Wake up Notification is transmitted after Notification Report is Transmitted |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Lifeline: Include command classes: Battery report, Notification report, and Device Reset Locally notification, Binary report. |
2 | 5 | Root Device: Binary Sensor Command Class: Compatible with 300 series1 -Binary Sensor reports status of CO or no CO via Lifeline.2-When the sensor detects status change of CO and no CO, the device will be triggered. |
3 | 5 | Root Device: Notification reports status of detect CO or no CO via Lifeline.2-When the sensor detects status change of CO and no CO, the device will be triggered. |
Dimensions | 0.0790000x0.0790000x0.0790000 mm |
Weight | 46.5 gr |
Hardware Platform | ZM5202 |
EAN | 6971348970055 |
IP Class | IP 20 |
Voltage | 3V |
Battery Type | 1 * CR123A |
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-16095241 |
Z-Wave Product Id | 0x0260.0x8005.0x1000 |
Communications Connections | Ethernet (Wireless/WiFi) |
Outdoor Use | ok |
Firmware Updatable | Not Updatable |
Communications Protocol | Z-Wave Serial API |
Color | White |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |