Quickstart

This is a Notification Sensor for XXXQFrequencyName. To run this device please connect it to your mains power supply. Press the Network Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second.
If add Process is successful, Green LED will turn on.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The smart combustible gas sensor is designed to detect methane(CH4), and sound alarm to remind people of the danger, it can also send notification to users‘ smart phone via gateway to remind of people remotely. it adopts Z-Wave wireless transmission technology. With the characteristics of high sensitivity and stablization, it can avoid fire or explosion happened in advance.

Installation

Liquefied petroleum gas should be installed at 0.3-1m height from floor and semi-conductor of sensor installation position to gas source should be less than 1.5m. Natural gas, manufactured gas, marsh gas, etc. should be be installed at 0.3-1m below from ceiling, semi-diameter to gas source less than 1.5m.

Product Usage

1. Shell surface will be slightly hot while working, which is normal phenomenon

2. Please dismantle sensor while decorating house

3. Avoid spraying aerosol around sensor

4. Oil adhension around gas convection holes may effect the sensitivity of gas sensor after long time of use. It‘s suggested to clear gas convection holes every 3 months (with little detergent, but with care so it doesn‘t enter the body of the sensor).

5. Semi-conductor of gas sensor has 5-year lifespan

6. Don‘t use lighter to test the sensor directly

Starting up

The green LED lights up after power on the sensor, when a beep sounds once, the sensor enters into warm-up state then red and yellow LED flashes alternately. Eventually, the flash stops 3 minutes later, which indicates that the sensor has entered into a normal working state. Don‘t the senor while it‘s in warm-up state.

LIGHT STATE & PRODUCT TEST

STATE	COLOR	LIGHT	ALARM SOUND
Power	Green	Normally on	No
Alarm	Red	Flashing	gas alarm
Malfunction	Yellow	Normally on	Long buzz

Test button of this sensor is used for testing wheater LED indicator and buzzer can work properly. Red LED and yellow LED flash alternatively with buzzer alarm when the test button is pressed.

Reset to factory default	-Long press Net_Button at least 10 seconds in the device. -Device Reset Locally notification is Transmitted.
Inclusion	Press the Network Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second. If add Process is successful, Green LED will turn on.
Exclusion	Press the Network Button 3 times within 1.5s If remove Process is successful, Green LED is Blinking 6 times, then turn on
NIF	XXXNIF
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	1	Lifeline association group Include command classes: Notification Report and Device Reset Locally notification.
2	5	Root Device group(Notification). Notification reports status of gas detected or no gas detected via Lifeline. When the sensor detects status change of gas detected and no gas detected, the device will be triggered.

Technical Data

Dimensions	78 x 78 x 67 mm mm
Weight	91 gr
Hardware Platform	ZM5202
EAN	6971348970062
IP Class	IP 20
Voltage	230 V
Device Type	Notification Sensor
Network Operation	Always On Slave
Z-Wave Version	6.51.09
Certification ID	ZC10-16125343
Z-Wave Product Id	0x0260.0x8003.0x1000
Communications Protocol	Z-Wave Serial API
Electric Load Type
IP (Ingress Protection) Rated	ok
Color	White
Sensors
Communications Connections	Ethernet (Wireless/WiFi)
Frequency	Europe - 868,4 Mhz
Maximum transmission power	5 mW

Heiman

Smart Combustible Gas Sensor