Quickstart

This is a secure Notification Sensor for XXXQFrequencyName. To run this device please insert fresh 1 * CR123A batteries. To run this device please make sure the internal battery is fully charged. - Press the Net_Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second.
- If Inclusion Process is successful, Green led will turn off.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The smart smoke sensor detects smoke, and sends an alarm signals to alertof danger.When the smart smoke sensor detects smoke, it will send an alarm notification to your gateway through wireless Z-Wave communication protocol.Then the gateway will send the notification to the server, the server interprets the signal and transfers the signal to users‘ APP. The smart smoke sensor has high stabilityand sensitivity,which will alert house of fire effectively.

Installation

- Flat ceiling mounting

The preferred location to install smoke sensor is in the centre of the ceiling, because smoke,  heat and combusible products rise to ceiling and will laterally spread. Keep at least 30 cm distance  from lights or decoration and at least 17cm away from walls and corners.

- Sloping ceiling mounting

If ceiling is sloping, please install the smok sensor at horizontal distance 90 cm away from the ceiling top.


Installation guide

 
- Anticlockwise rotation the bracket out from the installation base.



- Fixed the bracket intoceiling using srews.
- Remove the double-sided adhersive and stickalarm into ceiling


- Remove the battery insulating strip to make detector on power and clockwise rotating alarm into bracket.

Product Usage



Reset to factory default - Long press Net-Button while installing batteries in HS1SA-Z.
- Device Reset Locally notification is Transmitted.
Inclusion Press the Net-Button 3 times within 1.5s, Green LED is Blinking 3 times within 1 second.
If Inclusion Process is successful, Green led will turn off.
Exclusion - Press the Net_Button 3 times within 1.5s
- If Exclusion Process is successful, Green led is Blinking 6 times, then turn off.
NIF Press network button once.
Wakeup -Wake up Notification is transmitted every 24 hours by default.
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Lifeline
2 5 (V3.1 and higher) Root Device group (Notification) 1. Notification reports reports status of detect smoke or no smoke via Lifeline. 2. When the sensor detects status change between smoke and no smoke, the device will be triggered.
(2) 5 (only for older devices V1.0) Root Device group - (Binary Sensor) Compatible with 300 series 1. Binary Sensor reports status of smoke or no smoke via Lifeline.2.When the sensor detects status change between smoke and no smoke, the device will be triggered.
(3) 5 (only for older devices V1.0) Root Device group(Notification) 1. Notification reports reports status of detect smoke or no smoke via Lifeline. 2. When the sensor detects status change between smoke and no smoke, the device will be triggered.

Technical Data

Dimensions 0.0599200x0.0503400x0.0599200 mm
Weight 50 gr
Hardware Platform ZM5202
EAN 6971348970048
IP Class IP 20
Voltage 3V
Battery Type 1 * CR123A
Device Type Notification Sensor
Network Operation Reporting Sleeping Slave
Firmware Version 03.01
Z-Wave Version 05.03
Certification ID ZC10-18076198
Z-Wave Product Id 0x0260.0x8002.0x1000
Outdoor Use ok
IP (Ingress Protection) Rated ok
Firmware Updatable Not Updatable
Communications Protocol Z-Wave Serial API
Communications Connections Ethernet (Wireless/WiFi)
Color White
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeNotification Sensor