Hank

Flood Sensor

SKU: HNKEFLD01

ZWave+ Security V2

Quickstart

This is a secure Water Sensor for XXXQFrequencyName. To run this device please make sure the internal battery is fully charged. To add this device to your network execute the following action:

Click the Z-button once or triple click the Z-button quickly, the LED indicator should blink fast in blue.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Flood Sensor is capable of both detecting leaks and floods and when the level of water gets too low in pool or tank, Flood Sensor can work with your z-wave network to prevent emergencies such as burst water boiler to leaking air conditioners. With Z-Wave, the scope to save money is endless.

Installation

Flood Sensor should not be mounted directly on or near metal framing or other large metallic objects since metal objects may weaken the radio signal strength. After “activation” process, the sensor can work without any installation. Furthermore, you can
use the extension probe to fix sensor body.
Reset to factory default Press and hold the Z-button for more than 20 seconds.
Inclusion
Click the Z-button once or triple click the Z-button quickly, the LED indicator should blink fast in blue.
Exclusion
Click the Z-button once or triple click the Z-button quickly, the LED indicator should blink fast in orange.
NIF XXXNIF
Wakeup Press Z-Button
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Lifeline
2 5 On/Off Control -- Note parameter 14

Configuration Parameters

Parameter 14: Enable/Disable BASIC SET command

Flood sensor can send BASIC SET command to nodes associated with group 2.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable
1 Enable

Parameter 15: Value of the BASIC SET

Flood sensor can reverse its value of BASIC SET when flooding is triggered.
Size: 1 Byte, Default Value: 0

Setting Description
0 Send BASIC SET VALUE = 255 to nodes associated with group 2 when flooding alarm is triggered. Send BASIC SET VALUE = 0 to nodes associated with group 2 when flooding alarm is canceled.
1 Send BASIC SET VALUE = 0 to nodes associated with group 2 when flooding alarm is triggered. Send BASIC SET VALUE = 255 to nodes associated with group 2 when flooding alarm is canceled.

Parameter 17: Enable/Disable flooding alarm


Size: 1 Byte, Default Value: 1

Setting Description
0 Disable
1 Enable

Parameter 18: Enable/Disable shock alarm


Size: 1 Byte, Default Value: 0

Setting Description
0 Disable
1 Enable

Parameter 19: Temperatur report Time

The sensor measure the temperaure every ten minutes, change of 1 degree Celsius will be reported. By default, it must report at least once a day.
Size: 1 Byte, Default Value: 144

Setting Description
3 - 240 Report time

Parameter 20: Set the high temperature alarm trigger value


Size: 2 Byte, Default Value: 400

Setting Description
-550 - 1250 - 55 - +125°C

Parameter 21: Enable/Disable low temperature alarm


Size: 0 Byte, Default Value: 1

Setting Description
0 Disable
1 Enable

Parameter 22: Set the low temperature alarm trigger value


Size: 2 Byte, Default Value: 0

Setting Description
-550 - 1250 -55 - +125°C

Parameter 24: Enable/Disable blinking LED when alarm being triggered


Size: 1 Byte, Default Value: 1

Setting Description
0 Disable
1 Enable

Parameter 32: Level of low battery

This parameter defines a battery level as the “low battery”.
Size: 1 Byte, Default Value: 20

Setting Description
10 - 50 %

Technical Data

Dimensions 0.0680000x0.0250000x0.0680000 mm
Weight 34 gr
Hardware Platform ZM5101
EAN 6925312930026
IP Class IP 20
Voltage 3,6V
Device Type Water Sensor
Network Operation Sleeping device
Firmware Version 01.02
Z-Wave Version 04.3d
Certification ID ZC10-17125894
Z-Wave Product Id 0x0208.0x0200.0x000f
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeWater Sensor