This is a
1) Connect the power supply.
2) Set the Z-Wave network main controller into inclusion mode (see Z-Wave network controller operating manual).
3) Triple click the Z-button or power up the device , RGB LED indicator should blink fast in blue.4) Smart Plug should be recognized and included into the Z-Wave network.
Smart plug is a Z-Wave Switch plugin module specifically used to enable Z-Wave command and control (on/off) of any plug-in tool. It can report wattage consumption or kWh energy usage, and can indicate the power level with a RGB LED. Smart Plug is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade .
Reset to factory default | 1) Insert the Plug into a socket 2) Press and hold the Z button for more than 20 seconds 3) If holding time more than 20 seconds, the RGB LED indicator will keep yellow for 2 seconds, which means resetting is completed. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
Inclusion | Triple click the Z-button or power up the device , RGB LED indicator should blink fast in blue. |
Exclusion | Triple click the Z button. RGB LED indicator will blink orange till the removing process is completed, than the indicator will keep orange for 3 seconds. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline |
Smart Plug keep detecting the load power, once the AC current exceeds 16.5A for more than 5s, smart plug‘s relay will turn off. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The function is disabled |
1 | The function is enabled. |
Define how the Plug reacts after the power supply is back on. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Smart Plug memorizes its state after a power failure. |
1 | Smart Plug does not memorize its state after a power failure. Connected device will be on after the power supply is reconnected. |
2 | Smart Plug does not memorize its state after a power failure. Connected device will be off after the power supply is reconnected. |
Smart Plug can send notifications to associated device (Group Lifeline) when the status of smart plug’s load is changed. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The function is disabled. |
1 | Send Basic report. |
2 | Send Basic report only when Load status is not changed by Z-WAVE Command. |
After smart plug being included into a Z-Wave network, the RGB LED indicator will indicate the situation of load. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Power indication mode. |
1 | Momentary indicate mode. |
When the change value of load power exceeds the setting value, smart plug will send meter report (watt) to associated device (Group Lifeline). Size: 2 Byte, Default Value: 50
Setting | Description |
---|---|
0 | Disable |
1 - 65535 | Watt |
Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 | Disable |
1 - 255 | % |
The interval time of sending meter report (watt) to associated device (Group Lifeline). Size: 4 Byte, Default Value: 30
Setting | Description |
---|---|
0 | Disable |
5 - 2678400 | Seconds |
The interval of sending meter report (KWh) to association device (Group Lifeline). Size: 4 Byte, Default Value: 300
Setting | Description |
---|---|
0 | Disable |
5 - 2678400 | Seconds |
Setting time for sending meter report (voltage) Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
5 - 2678400 | Seconds |
The interval time of sending meter report (current) to associated device (Group Lifeline). Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Diasable |
5 - 2678400 | Seconds |
Lock/unlock all configuration parameters. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Unlock |
1 | Lock |
Size: 4 Byte, Default Value: 1
Setting | Description |
---|---|
85 | Reset the values of the configuration command to default setting. |
1431655765 | Smart Plug will send “Device_Reset_Locally”, remove from the Z-Wave network and reset to factory default. |
Dimensions | 0.0618300x0.0721300x0.1147000 mm |
Weight | 162.49 gr |
Hardware Platform | ZM5101 |
EAN | 6925312930187 |
IP Class | IP 20 |
Voltage | 230V |
Load | 2300 W |
Device Type | On/Off Power Switch |
Network Operation | Always On Slave |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-16075153 |
Z-Wave Product Id | 0x0208.0x0100.0x000A |
Firmware Updatable | Updatable by Consumer by RF |
Supported Meter Type | Electric Energy |
Color | |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |