This is a
Leading edge for inductive loads
|
Trailing edge for capacitive or resistive loads
|
On/off only
|
Automatically detection
|
---|---|---|---|
Orange LED flashing
|
Green LED flashing
|
Orange and Green LEDs flashing together
|
Orange and Green LEDs flashing alternately
|
Reset to factory default | Press 10 times of any button or exclude the device from Z-Wave network, then cut off the main power. The factory setting will be restored. |
Inclusion | 1. Set controller into Add mode and press 3 clicks on "+" or "-" button to add. If succeed, green LED flicks 4 times.
2. If an external switch panel wired, press/toggle the button on that panel 3 times also can add the network (To make the external panel work, set the parameter 14 with value 1, 2, 3 or 4). |
Exclusion | 1. Set controller into Remove mode, and press 3 clicks on "+" or "-" button to remove. If succeed, green LED flicks 4 times.
2. If an external switch panel wired, press/toggle the button on that panel 3 times also can remove the network (To make the external panel work, set the parameter 14 with value 1, 2, 3 or 4). |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Lifeline - Send unsolicited reports to the gateway |
2 | 5 | Send Switch_Multilevel CC to associated devices |
5 | 5 | Associate with Key “+” Send Basic Set CC to associated devices |
8 | 5 | Associate with Key “-” Send Basic Set CC to associated devices |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | not saved,Dimmer will be off when powered again |
1 | saved,Dimmer will keep the same state when powered again |
Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | leading edge |
1 | trailing edge |
2 | On/off only |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Auto detection disabled |
1 | Auto detection enabled |
Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 | LED disabled |
1 - 10 | Min level - Max level |
The max level should always higher than min level Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 98 | percentage brightness level |
The max level should always higher than min level Size: 1 Byte, Default Value: 99
Setting | Description |
---|---|
2 - 99 | percentage brightness level |
Manual control realized by holding external button Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 2550 | Max 2.55s, in 10ms steps |
Manual control realized by holding external button Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | percentage value (modification isn’t recommended) |
Auto control realized by: - one click; - double click of external button; - send Z-Wave CC Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 2550 | Max 2.55s, in 10ms steps |
Auto control realized by: - one click; - double click of external button; - send Z-Wave CC Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | percentage value (modification isn’t recommended) |
With this parameter you can set the light level the lamp will reach when you turn on the lamp of single touch “+” Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | the percentage get by the last button-holding touch |
1 - 99 | percentage value |
Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 | No report during dimming |
1 - 255 | send report in1-255*10ms interval |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Button (Momentary buttons ) |
1 | Toggle (2-state Switches ) |
Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | function disabled |
1 | wire 1 ex.switch key to S1 only |
2 | wire 1 ex.switch key to S2 only |
3 | wire 2 ex.switch keys to S1 and S2,each key can control both dimming directions |
4 | wire 2 ex.switch keys to S1 and S2, each key control one dimming direction |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Watt |
2 | KWH |
4 | Ampere |
8 | Voltage |
15 | All |
Size: Byte, Default Value: 16
Setting | Description |
---|---|
1 - 255 | n*1sec |
Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | beep disabled |
1 | beep enabled |
Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | alarm disabled |
1 - 5000 | 1-5000*0.01 A alarm enabled |
Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | alarm disabled |
1 - 10000 | 1-10000*0.1 V alarm enabled |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
85 | FF Factory setting |
Dimensions | 0.0860000x0.0860000x0.0420000 mm |
Weight | 156 gr |
Hardware Platform | ZM5202 |
EAN | 6928954212000 |
IP Class | IP 20 |
Voltage | 230 V |
Load | 20 - 200W |
Device Type | Dimmer |
Generic Device Class | Multilevel Switch |
Specific Device Class | Routing Multilevel Switch |
Firmware Version | 02.06 |
Z-Wave Version | 04.3e |
Z-Wave Product Id | 0x015f.0xd311.0x5102 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |