This is a
Dimmer Switch is a wall panel built-in with Z-Wave Plus module. With its stylish design and stable performance, the panel can be used to control the light level. It supports basic command class,multi channel command class and multi channel association command class, also works as a repeater in a Z-Wave network. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from any other manufacturers.
Leading edge for inductive loads
|
Trailing edge for capacitive or resistive loads | On/off only | Automatically detection |
---|---|---|---|
Orange LED flashing | Green LED flashing | Orange and Green LEDs flashing together |
Orange and Green LEDs flashing alternately
|
Reset to factory default | Press 10 times of any button or exclude the device from Z-Wave network, then cut off the main power. The factory setting will be restored. |
Inclusion | 1. Set controller into Add mode and press 3 clicks on "+" or "-" button to add. If succeed, green LED flicks 4 times.
2. If an external switch panel wired, press/toggle the button on that panel 3 times also can add the network (To make the external panel work, set the parameter 14 with value 1, 2, 3 or 4). |
Exclusion | 1. Set controller into Remove mode, and press 3 clicks on "+" or "-" button to remove. If succeed, green LED flicks 4 times.
2. If an external switch panel wired, press/toggle the button on that panel 3 times also can remove the network (To make the external panel work, set the parameter 14 with value 1, 2, 3 or 4). |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Lifeline - Send unsolicited reports to the gateway |
2 | 5 | Send Switch_Multilevel CC to associated devices |
5 | 5 | Associate with Key “+” Send Basic Set CC to associated devices |
8 | 5 | Associate with Key “-” Send Basic Set CC to associated devices |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | not saved,Dimmer will be off when powered again |
1 | saved,Dimmer will keep the same state when powered again |
Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | leading edge |
1 | trailing edge |
2 | On/off only |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Auto detection disabled |
1 | Auto detection enabled |
Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 | LED disabled |
1 - 10 | Min level - Max level |
The max level should always higher than min level Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 98 | percentage brightness level |
The max level should always higher than min level Size: 1 Byte, Default Value: 99
Setting | Description |
---|---|
2 - 99 | percentage brightness level |
Manual control realized by holding external button Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 2550 | Max 2.55s, in 10ms steps |
Manual control realized by holding external button Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | percentage value (modification isn’t recommended) |
Auto control realized by: - one click; - double click of external button; - send Z-Wave CC Size: 2 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 2550 | Max 2.55s, in 10ms steps |
Auto control realized by: - one click; - double click of external button; - send Z-Wave CC Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | percentage value (modification isn’t recommended) |
With this parameter you can set the light level the lamp will reach when you turn on the lamp of single touch “+” Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | the percentage get by the last button-holding touch |
1 - 99 | percentage value |
Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 | No report during dimming |
1 - 255 | send report in1-255*10ms interval |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Button (Momentary buttons ) |
1 | Toggle (2-state Switches ) |
Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | function disabled |
1 | wire 1 ex.switch key to S1 only |
2 | wire 1 ex.switch key to S2 only |
3 | wire 2 ex.switch keys to S1 and S2,each key can control both dimming directions |
4 | wire 2 ex.switch keys to S1 and S2, each key control one dimming direction |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Watt |
2 | KWH |
4 | Ampere |
8 | Voltage |
15 | All |
Size: Byte, Default Value: 16
Setting | Description |
---|---|
1 - 255 | n*1sec |
Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | beep disabled |
1 | beep enabled |
Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | alarm disabled |
1 - 5000 | 1-5000*0.01 A alarm enabled |
Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | alarm disabled |
1 - 10000 | 1-10000*0.1 V alarm enabled |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
85 | FF Factory setting |
Dimensions | 0.0860000x0.0860000x0.0410000 mm |
Weight | 165 gr |
Hardware Platform | ZM5202 |
EAN | 692895421307 |
IP Class | IP 20 |
Voltage | 230 V |
Load | 20 - 200 W |
Device Type | Dimmer |
Generic Device Class | Multilevel Switch |
Specific Device Class | Routing Multilevel Switch |
Firmware Version | 02.06 |
Z-Wave Version | 04.3e |
Z-Wave Product Id | 0x015f.0xd411.0x5102 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |