Quickstart

This is a Static Controller for Europe. To run this device please connect it to your mains power supply.

C This device is a Z-Wave control center. The device is controlled via webinterface. To find the devices IP address create an account at the miCasaverde homepage and click in the tab "Support" then "Setup" and "VeraLite". Include other devices to the Veras network in the menu "Devices" with "Add Device", then "Add Z-Wave Devices". Exclude devices using the menu "Devices" with "Add Devices", then "Advanced Z_Wave Devices", then "Remove one".



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

The miCasaverde Vera Lite is a consumer electronics device used for home automation. Vera Lite gateway communicates with electronic sensors and devices located throughout home using wireless and wired communications and connects to central portal server using existing broadband connection (Cable or DSL).

Internal Z-Wave interface module allows user to control Z-Wave sensors, appliance controls and automation devices.

Vera Lite integrates multiple complicated control, automation and internet protocols into one simple plug"n"play device. It provides a clear, consistent interface that allows user to manage home easily, whether at home, office or using mobile phone on the road.

The Vera Lite works with the MIOS Web-OS.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Vera Lite Setup -> Advanced -> Backup -> Restore Factory Defaults

Alternatively you can reset the Vera Lite by pushing the reset button with a stick for at least 10 seconds.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Installation

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

  1. Select "Device" within the Vera Lites menu.
  2. Confirm the button "Add Devices".
  3. Confirm the button "Advanced Z-Wave Devices".
  4. Confirm the button "Add VERA to another Z-Wave netowrk".

Alternatively, for Inclusion and Exclusion of devices you can power the Vera with 4 x AA batteries. You can carry out the function directly near the device by using the hardware buttons on the Vera Lite.

Exclusion

  1. Select "Device" within the Vera Lites menu.
  2. Confirm the button "Add Devices".
  3. Confirm the button "Advanced Z-Wave Devices".
  4. Confirm the button "Add VERA to another Z-Wave netowrk".

Alternatively, for Inclusion and Exclusion of devices you can power the Vera with 4 x AA batteries. You can carry out the function directly near the device by using the hardware buttons on the Vera Lite.

Product Usage

With the webinterface you can control actuators like dimmer, thermostats and electrical switches and you can see information and data from your sensors. Further information you can find directly on the website.

Node Information Frame

The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame. To issue a NIF execute the following action:

To send out a Node Information Frame type in the following line into your browsers address bar and replace the IP with the IP of your device:

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Special Operations as Z-Wave Controller

As long as this device is not included into a Z-Wave network of a different controller it is able to manage its own Z-Wave network as primary controller. As a primary controller the device can include and exclude other devices in its own network, manage associations, and reorganize the network in case of problems. The following controller functions are supported:

Inclusion of other devices

Communication between two Z-Wave devices only works if both belong to the same wireless network. Joining a network is called inclusion and is initiated by a controller. The controller needs to be turned into the inclusion mode. Once in this inclusion mode the other device needs to confirm the inclusion - typically by pressing a button.

If current primary controller in your network is in special SIS mode this and any other secondary controller can also include and exclude devices.

To become primary a contoller have to be resetted and then include a device.

  1. Select "Device" within the Vera Lites menu.
  2. Confirm the button "Add Device".
  3. Confirm the button "Add Z-Wave Devices".
  4. Confirm the inclusion at the device. See the devices manuals for details how to include them at the icon I.
  5. The new device now should appear on the user interface.

If the inclusion fails maybe it is already included in a different Z-Wave network. You can exclude the device and repeat the steps for inclusion.

Exclusion of other devices

The primary controller can exclude devices from the Z-Wave network. During exclusion the relationship between the device and the network of this controller is terminated. No communication between the device and other devices still in the network can happen after a successful exclusion. The controller needs to be turned into the exclusion mode. Once in this exclusion mode the other device needs to confirm the exclusion - typically by pressing a button.

Attention: Removing a device from the network means that it is turned back into factory default status. This process can also exclude devices from it's previous network.

  1. Select "Device" within the Vera Lites menu.
  2. Confirm the button "Add Devices".
  3. Confirm the button "Advanced Z-Wave Devices".
  4. Confirm the button "Remove one".
  5. Confirm the exclusion at the device. See the devices manuals for details how to include them at the icon I.
  6. The device now should disappear on the user interface.

Management of Association in the controller

  1. Select "Dashboard" within the Vera Lites menu.
  2. Pick the devices widget and hit the wrench icon on top right side.
  3. Confirm the button "Device Options".
  4. Within this dialog you can configure the association groups and actuators.
  5. Battery powered devices with association function need to be woken up to get the settings.

Technical Data

Dimensions 0.0120000x0.0100000x0.0040000 mm
Weight 320 gr
EAN 728028227765
Device Type Static Controller
Generic Device Class Static Controller
Firmware Version 01.00
Z-Wave Version 03.14
Certification ID ZC08-10090001
Z-Wave Product Id 008c.0001.0001
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW

Supported Command Classes

  • Basic
  • Controller Replication
  • Manufacturer Specific
  • Version
  • Clock

Explanation of Z-Wave specific terms