Ingersoll Rand - Nexia Home Intelligence
Nexia One Touch
SKU: NX1000
Quickstart
This is a
1.Put primary controller into inclusionmode2.Press any button to wake the One Touch3.Press and hold the middle page button (round button) until the Installer Setup menu appears4.Select the 'Z-Wave' button5.Select the 'Include' button6.Include will fast flash and then SUCCESS will display briefly
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The Nexia One Touch is a wall controller device that can act as a central scene controller or a traditional stand-alone scene controller.The Nexia One Touch contains up to 15 different scenes organized in 3 pages of screen where each page contains 5 scenes.The Nexia One Touch conveniently runs up to 15 modes and automations with the tap of a button.
| Reset to factory default | Please use Factory Reset as a last resort option only as all network settings and associations will be cleared. 1.Press any button to wake the One Touch2.Press and hold the middle page button (round button) until the Installer Setup menu appears3.Select the 'System' button4.Select the 'Factory Reset' button5.Select 'Yes' to proceed with the factory reset |
| Inclusion | 1.Put primary controller into inclusionmode2.Press any button to wake the One Touch3.Press and hold the middle page button (round button) until the Installer Setup menu appears4.Select the 'Z-Wave' button5.Select the 'Include' button6.Include will fast flash and then SUCCESS will display briefly |
| Exclusion | 1.Put primary controller into exclusion mode2.Press any button to wake the One Touch3.Press and hold the middle page button (round button) until the Installer Setup menu appears4.Select the 'Z-Wave' button5.Select the 'Exclude' button6.Exclude will fast flash and then SUCCESS will display briefly |
| NIF | XXXNIF |
| Wakeup | When the backlight and/or screen is off, the first page (round)button press will wake the One Touch causing it to send a Wakeup Notification report.The One Touch has a 6 hour default wakeup interval and will send the Wakeup Notification once that interval expires. WAKEUP_INTERVAL_CAPABILITIES_REPORTMin Wake Up Interval : 4200 secondsMax Wake Up Interval: 86400 secondsDefault Wake Up Interval: 21600 secondsWake Up Interval Step: 10 |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 2 | Profile: General:LifelineName: Z-Wave Plus LifelineCommand Class List:Battery ReportCentral Scene NotificationDevice Reset Locally Notification |
| 2 | 2 | Profile: Control: Key1Name: Button1 Basic SetCommand Class List:Basic Set |
| 3 | 2 | Profile: Control: Key2Name: Button2 Basic SetCommand Class List:Basic Set |
| 4 | 2 | Profile: Control: Key3Name: Button3 Basic SetCommand Class List:Basic Set |
| 5 | 2 | Profile: Control: Key4Name: Button4 Basic SetCommand Class List:Basic Set |
| 6 | 2 | Profile: Control: Key5Name: Button5 Basic SetCommand Class List:Basic Set |
| 7 | 2 | Profile: Control: Key6Name: Button6 Basic SetCommand Class List:Basic Set |
| 8 | 2 | Profile: Control: Key7Name: Button7 Basic SetCommand Class List:Basic Set |
| 9 | 2 | Profile: Control: Key8Name: Button8 Basic SetCommand Class List:Basic Set |
| 10 | 2 | Profile: Control: Key9Name: Button9 Basic SetCommand Class List:Basic Set |
| 11 | 2 | Profile: Control: Key10Name: Button10 Basic SetCommand Class List:Basic Set |
| 12 | 2 | Profile: Control: Key11Name: Button11 Basic SetCommand Class List:Basic Set |
| 13 | 2 | Profile: Control: Key12Name: Button12 Basic SetCommand Class List:Basic Set |
| 14 | 2 | Profile: Control: Key13Name: Button13 Basic SetCommand Class List:Basic Set |
| 15 | 2 | Profile: Control: Key14Name: Button14 Basic SetCommand Class List:Basic Set |
| 16 | 2 | Profile: Control: Key15Name: Button15 Basic SetCommand Class List:Basic Set |
| 17 | 2 | Profile: Control: Key1Name: Button1Command Class List:Scene Activation Set |
| 18 | 2 | Profile: Control: Key2Name: Button2Command Class List:Scene Activation Set |
| 19 | 2 | Profile: Control: Key3Name: Button3Command Class List:Scene Activation Set |
| 20 | 2 | Profile: Control: Key4Name: Button4Command Class List:Scene Activation Set |
| 21 | 2 | Profile: Control: Key5Name: Button5Command Class List:Scene Activation Set |
| 22 | 2 | Profile: Control: Key6Name: Button6Command Class List:Scene Activation Set |
| 23 | 2 | Profile: Control: Key7Name: Button7Command Class List:Scene Activation Set |
| 24 | 2 | Profile: Control: Key8Name: Button8Command Class List:Scene Activation Set |
| 25 | 2 | Profile: Control: Key9Name: Button9Command Class List:Scene Activation Set |
| 26 | 2 | Profile: Control: Key10Name: Button10Command Class List:Scene Activation Set |
| 27 | 2 | Profile: Control: Key11Name: Button11Command Class List:Scene Activation Set |
| 28 | 2 | Profile: Control: Key12Name: Button12Command Class List:Scene Activation Set |
| 29 | 2 | Profile: Control: Key13Name: Button13Command Class List:Scene Activation Set |
| 30 | 2 | Profile: Control: Key14Name: Button14Command Class List:Scene Activation Set |
| 31 | 2 | Profile: Control: Key15Name: Button15Command Class List:Scene Activation Set |
| 32 | 2 | Profile: Control: Key1Name: Button1Command Class List:Thermostat Setpoint Set |
| 33 | 2 | Profile: Control: Key2Name: Button2Command Class List:Thermostat Setpoint Set |
| 34 | 2 | Profile: Control: Key3Name: Button3Command Class List:Thermostat Setpoint Set |
| 35 | 2 | Profile: Control: Key4Name: Button4Command Class List:Thermostat Setpoint Set |
| 36 | 2 | Profile: Control: Key5Name: Button5Command Class List:Thermostat Setpoint Set |
| 37 | 2 | Profile: Control: Key6Name: Button6Command Class List:Thermostat Setpoint Set |
| 38 | 2 | Profile: Control: Key7Name: Button7Command Class List:Thermostat Setpoint Set |
| 39 | 2 | Profile: Control: Key8Name: Button8Command Class List:Thermostat Setpoint Set |
| 40 | 2 | Profile: Control: Key9Name: Button9Command Class List:Thermostat Setpoint Set |
| 41 | 2 | Profile: Control: Key10Name: Button10Command Class List:Thermostat Setpoint Set |
| 42 | 2 | Profile: Control: Key11Name: Button11Command Class List:Thermostat Setpoint Set |
| 43 | 2 | Profile: Control: Key12Name: Button12Command Class List:Thermostat Setpoint Set |
| 44 | 2 | Profile: Control: Key13Name: Button13Command Class List:Thermostat Setpoint Set |
| 45 | 2 | Profile: Control: Key14Name: Button15Command Class List:Thermostat Setpoint Set |
| 46 | 2 | Profile: Control: Key15Name: Button15Command Class List:Thermostat Setpoint Set |
Configuration Parameters
Parameter 1: Reserved
Reserved Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Reserved |
Parameter 10: Button 9 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 11: Button 10 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 12: Button 11 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 13: Button 12 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 14: Button 13 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 15: Button 14 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 16: Button 15 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 17: Reserved
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|
Parameter 18: Reserved
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|
Parameter 19: Reserved
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|
Parameter 2: Button 1 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 20: Touch Calibration
Button touch calibration sensitivity level Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 1 - 10 | 1 = Least Sensitive 10 = Most Sensitive |
Parameter 21: Screen Contrast
Screen contrast level Size: 1 Byte, Default Value: 7
| Setting | Description |
|---|---|
| 1 - 10 | 1=less contrast, 10=more contrast |
Parameter 22: Reserved
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Reserved |
Parameter 23: Button LED Level
Button LED Brightness Level Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 1 - 10 | 1=10% 10 = 100% |
Parameter 24: Backlight Level
Backlight Brightness Level Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 1 - 10 | 1=10% 10 = 100% |
Parameter 25: Scene Button Press Backlight Timeout
Backlight timeout after a scene (rectangular) button press Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 10 - 15 | seconds |
Parameter 26: Page Button Press Backlight Timeout
Backlight timeout after a page (round) button press Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 5 - 15 | seconds |
Parameter 27: Reserved
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|
Parameter 28: Screen Timeout
Screen timeout- number of minutes after the last button press till the screen goes blank Size: 1 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 0 | disabled |
| 1 - 240 | minutes |
Parameter 29: Screen Timeout Primary Page
Page to default to after a screen timeout Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 3 | 0 = no change, 1=page1, 2=page2, 3=page3 |
Parameter 3: Button 2 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 30: Battery Stat Shutdown Threshold
Battery status shutdown threshold Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 - 20 | % |
Parameter 31: Battery Radio Cutoff Threshold
Battery % Radio Cutoff Threshold Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 40 | % |
Parameter 32: Battery LOWBATT Indicator Threshold
Low Battery % Indicator Threshold Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 5 - 50 | % |
Parameter 33: Battery Threshold Value for Midlevel
Battery % threshold for midlevel indicator Size: 1 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 30 - 80 | % |
Parameter 4: Button 3 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 5: Button 4 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 6: Button 5 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 7: Button 6 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Parameter 9: Button 8 Type
Configuration for the type of button and which commands it will send when pressed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 4 | 0x00 = Central Scene0x01 = Scene Control Momentary 0x02 = BASICSET Toggle 0x03 = Scene Control/BASICSET toggle0x04 = Thermostat |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Wall Controller |
| Network Operation | Portable Slave |
| Firmware Version | 01 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-15070012 |
| Z-Wave Product Id | 0x0178.0x5343.0x4735 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |