This is a Z-Wave Device for Europe.
To run this device please connect it to your mains power supply.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way
communication) and every mains powered node can act as a repeater for other nodes
(meshed network) in case the receiver is not in direct wireless range of the
transmitter.
This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.
If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.
Product Description
Start with us into the world of home automation. Turn your home into a Smart Home. Security, comfort, energy saving - everything is connected and makes your life easier and more comfortable.
You don"t know how you should start? No problem!
OOMI has already bundled a couple of components in this starter kit. The OOMI Home Lighting Starter Kit offers a mix between security and monitoring, light and ambience and of course automation.
With OOMI Lighting Starter Kit you can supervise your home with the OOMI Cube even at night, you can control any electrical devices and its energy consumption with the OOMI Plug and you can create an unique room atmosphere with the OOMI Bulb.
OOMI Touch
the central touchpad for all your OOMI devices
User-friendly user interface
Create own automation scenes and manage them
Watch tutorials
Control your TV and other IR devices via the integrated IR interface
Integrate other Z-Wave devices like binary switches (please be aware that OOMI continously works on the integration of other Z-Wave devices)
OOMI Cube
Control unit of your smart home
Control of all functions of any electrical devices
Security camera with night vision
OOMI Infinity Dock
Charging station for OOMI Touch
OOMI Bulb
2 pc. into the Starter Kit
Creation of your individual room atmosphere by colors
Energy efficient (9watts), 750 Lumens (60watts equivalent)
Dimmable
Up to 30.000 hours
16 Million colors and warm white light
OOMI Plug Type F
Remote controllable adapter to monitor and control electrical devices
Energy measurement function
USB charger
LED ring provides the energy consumption
LED ring as a nightlight
Wireless on/off control of any electrical device
Features:
Starter Kit with control unit and 5 single devices
Comprehensive bundle package allows different automation scenes and functions
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing
Technical Data
Dimensions
0.2400000x0.1300000x0.2400000 mm
Weight
1915 gr
EAN
6923060104041
Certification ID
ZC10-17055600
Frequency
Europe - 868,4 Mhz
Maximum transmission power
5 mW
Explanation of Z-Wave specific terms
Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and
a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.