ZLINK
Z-Wave Plug-In On/Off Switch
SKU: PA-100
Quickstart
This is a
Place your Z-Wave controller in "Inclusion" mode. Then tap the button once to initiation Inclusion.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
ZLINK PA-100 is aZ-Wave Plus certified device with S2 security and SmartStart features. You can now add this device securely and with ease using QR code on the product with compatible gateways supporting S2 and Smart Start. PA-100 communicates with other Z-Wave certified devices and updates your home into a smart home. PA-100 can be used to turn On or Off lamps or AC operated appliances. Each Z-Wave device also serves as a node to repeat the signal in the network, thus, extending the overall Z-Wave mesh wireless network range.Additional Features: Power 120 VAC, 60Hz, up to 1800 watts Region US: 908.4, 916 MHz Works with incandescent, CFL & LED lights & appliances Plugs into Standard AC outlet LED backlit On/Off button Control lights or appliances via schedule or remotely Second wall AC outlet remains free Works with any gateway supporting Z-Wave
| Reset to factory default | 1. Unplug the PA-100 from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)2. Press and hold the button on the PA-1003. Plug the PA-100 back into the AC outlet with the button pressedAfter 3 seconds, release the button. If you see the button blink, that means that PA-100 has been reset successfully.Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
| Inclusion | Place your Z-Wave controller in "Inclusion" mode. Then tap the button once to initiation Inclusion. |
| Exclusion | Place your Z-Wave controller in "Exclusion" mode. Then tap the button to initiation Exclusion. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | 1. Z-Wave Plus Lifeline2. Device Reset Locally Notification |
Configuration Parameters
Parameter 3: Night Light
The LED indicator will be OFF when the connected light is ON and vice versa.When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 2 | When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 50.03 |
| Z-Wave Version | 6.81.00 |
| Certification ID | ZC10-18025998 |
| Z-Wave Product Id | 0x0315.0x4447.0x3031 |
| Electric Load Type | FluorescentIncandescentLED |
| Color | White |
| Outdoor Use | ok |
| Switch Type | Push Button Illuminated |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |