Philio
Flood sensor
SKU: PAT02-1C
Quickstart
This is a
1. Have Z-WaveController entered inclusion mode.2. Pressing the tamper key three times within 1.5 seconds to enter the inclusion mode.3. After add successful, the device will wake to receive the setting command from Z-Wave Controller about 20 seconds.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The flood multisensor PAT02 has flood, based on Z-Wavetechnology. It is theZ-Wave plus product, it support the security, OTA... Those newest features of theZ-Wave technology. Z-Wave is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and lightcommercial environments. The technology uses a low-power RF radio embedded or retrofitted into home electronics devices and systems, such as lighting, home access control, entertainment systems and household appliances. This product can be included and operated in any Z-Wave network with other Z-Wavecertified devices from other manufacturers and/or other applications.All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
| Reset to factory default | Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4 th pressed, and the LED will light ON.2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once.3. IDs are excluded and all settings will reset to factory default. |
| Inclusion | 1. Have Z-WaveController entered inclusion mode.2. Pressing the tamper key three times within 1.5 seconds to enter the inclusion mode.3. After add successful, the device will wake to receive the setting command from Z-Wave Controller about 20 seconds. |
| Exclusion | 1. Have Z-WaveController entered exclusion mode.2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode. Node ID has been excluded. |
| NIF | XXXNIF |
| Wakeup | When the device power on, the device will wake about 20 seconds. Inthis duration, the controller can communicate with the device. Normallythe device is always sleeping to save the battery energy. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 8 | The group 1 is for receiving the report message, like triggered event, temperature, humidity etc.And each group support 8 nodes. |
| 2 | 8 | The group 2 is for the light control, the device will send the Basic Set command to this group. And each group support 8 nodes. |
Configuration Parameters
Parameter 1: Basic Set OFF Level
Setting the BASIC command value. When the flood trigger off(0x00), send the BASIC CC to the group 2. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 255 | Setting the BASIC command value 0x00. |
Parameter 10: AutoReportBattery Time
The interval time for auto report the battery level. 0 means turn off auto report.The default value is 12. The tick time can setting by the configuration No.20. Size: 1 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 0 - 127 | The interval time for auto report thebattery level. |
Parameter 15: Auto Report Flood Time
The interval time for auto report the flood state. 0 means turn off auto report.The default value is 12. The tick time can setting by the configuration No.20. Size: 1 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 0 - 127 | The interval time for auto report the flood state. |
Parameter 2: Basic Set ON Level
Setting the BASIC command value.When the flood trigger on(0xFF), send the BASIC CC to the group 2. Size: 1 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 0 - 255 | Setting the BASIC command value 0xFF. |
Parameter 20: Auto Report Tick Interval
The interval time for auto report each tick. Setting this configuration will effect configuration No.10, No.13, No.14 and No.15. Units of one minute.Caution1: Setting to 0 means turn off all auto report function.Caution2: The value is unsigned byte Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 0 - 255 | The interval time for auto report each tick. |
Parameter 5: Operation Mode
Operation mode. Using bit to control. Size: 1 Byte, Default Value: 32
| Setting | Description |
|---|---|
| 1 | Disable the Flood function. |
Parameter 7: Customer Function
Customer function switch, using bit control. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 64 | Disable to report battery statewhen the device triggered. (1:Disable,0:Enable) |
| 32 | Disable Multi CC in auto report.(1:Disable, 0:Enable) |
| 16 | Notification Type, 0: Using Notification Report. 1: Using Sensor Binary Report. |
| 8 | Disable send out BASIC OFFafter the flood event cleared.(1:Disable, 0:Enable) |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | 01 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-15060011 |
| Z-Wave Product Id | 0x013C.0x0002.0x0021 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |