This is a
Place your Z-Wave controller in "Inclusion" mode. Then tap the button once to initiation Inclusion.
ZLINK PD-100 is a Z-Wave Plus certified device with S2 security and SmartStart features. You can now add this device securely and with ease using QR code on the product with compatible gateways supporting S2 and Smart Start. PD-100 communicates with other Z-Wave certified devices and updates your home into a smart home. PD-100 can be used to turn any plug in lamps into a smart lamp with dimmable light bulbs, turning it On, Off, or control dimming wirelessly. Each Z-Wave device also serves as a node to repeat the signal in the network, thus, extending the overall Z-Wave mesh wireless network range.Additional Features: Power 120 VAC, 60Hz, up to 300 watts Region US: 908.4, 916 MHz Works w/ most incandescent, dimmable CFL & LED lights Plugs into Standard AC outlet Remotely controls On, Off, or Dim levels Control lights via schedule LED backlit manual On/Off button Second wall AC outlet remains free Works with any certified gateway supporting Z-Wave
Reset to factory default | 1. Unplug the PD-100 from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)2. Press and hold the button on the PD-1003. Plug the PD-100 back into the AC outlet with the button pressedAfter 3 seconds, release the button. If you see the button blink, that means that PD-100 has been reset successfully.Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
Inclusion | Place your Z-Wave controller in "Inclusion" mode. Then tap the button once to initiation Inclusion. |
Exclusion | Place your Z-Wave controller in "Exclusion" mode. Then tap the button to initiation Exclusion. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | 1. Z-Wave Plus Lifeline2. Device Reset Locally Notification |
Parameter 10 indicates the time duration of each level. The resolution is 10 milliseconds. For example a default value of 3 means the timer runs out every 30 milliseconds. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | Parameter 10 indicates the time duration of each level. The resolution is 10 milliseconds. For example a default value of 3 means the timer runs out every 30 milliseconds. |
The LED indicator will be OFF when the connected light is ON and vice versa.When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 2 | When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status |
Parameter 9 indicates the number of levels when the lighting when the timer runs out. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | Parameter 9 indicates the number of levels when the lighting when the timer runs out. |
Hardware Platform | ZM5202 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 FW: 50.03 |
Z-Wave Version | 6.81.00 |
Certification ID | ZC10-18025997 |
Z-Wave Product Id | 0x0315.0x4744.0x3032 |
Outdoor Use | ok |
Firmware Updatable | Updatable by Consumer by RF |
Color | White |
Electric Load Type | Dimmable FluorescentDimmable LEDFluorescentIncandescentLED |
Switch Type | Push Button Illuminated |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |