This is a
2. Pressing Include button of PAD02 three times within 2 seconds will enter inclusion mode.
PAD02 is an E27(EU)/ E26(US) Edison screw based lamp socket, which provides electrical connection to the E14(EU)/ E12(US) Edison screw based lamps and support it in the lighting fixture. The use of socket allows lamps to be safely and conveniently replaced. You can On/Off the light by pressing the button briefly or a long pressing to control the brightness of dimmable lightbulb. This dimmer is a transceiver which is a security enabled device which based on Z-Wave Plus technology. Z-Wave Plus enabled devices displaying the Z-Wave Plus logo can also be used with it regardless of the manufacturer and can also be used in other manufacturers Z- Wave enabled networks. Remote dim level control of the connected light is possible with other manufacturers wireless Controller. Since PAD02 supports Security Command Class, it can learn with a Secured enabled controller to fully utilize the device. Its functionality and supported command classes is identical when included as a secure and non-secure device. Adding to Z- Wave Network In the front casing, there is an on/off button with LED indicator below which is used to switch on and off, dim level, or carries out add, remove, reset or association. When first power is applied, its LED flashes on and off alternately and repeatedly at 0.5 second intervals. It implies that it has not been assigned a node ID and start auto inclusion. Auto Inclusion The function of auto inclusion will be executed as long as the dimmer does not have Node ID and just connect the dimmer to main power. Note: Auto inclusion timeout is 2 minute during which the node information of explorer frame will be emitted once every several seconds. Unlike inclusion function as shown in the table below, the execution of auto inclusion is free from pressing the On/Off button on the dimmer.
Reset to factory default | 1. Pressing Include button of PAD02 three times within 2 seconds will enter inclusion mode. 2. Within 1 second, press Include button of PAD02 again for 5 seconds. 3. IDs are excluded. |
Inclusion | Pressing Include button of PAD02 three times within 2 seconds will enter inclusion mode. |
Exclusion | Pressing Include button of PAD02 three times within 2 seconds will enter exclusion mode. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Lifeline - The dimmer can be set to send reports to associated Z-Wave devices. It supports one association group with one node support for Grouping 1. For group 1, the dimmer will report ALARM_REPORT,DEVICE_RESET_LOCALLY_NOTIFICATION and MULTILEVEL_SWITCH_REPORT. |
2 | 5 | When the On/Off status changes or the dim level is achieved manually, it will send BASIC_SET command to group 2 nodes to make them unanimous. |
Whenever dimmer on/off state changes, it will send MULTILEVEL_SWITCH_REPORT to the nodes of group1. The default setting is Enable the function. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Disable |
1 | Show dimmer state |
1. Show dimmer Stateuff1aWhen dimmer is on, LED is on. When dimmer is off, LED is off. The default setting is Show dimmer State. 2. Show Night modeuff1aWhen dimmer is on, LED is off. When dimmer is off, LED is on. 3. One flash mode : When dimmer on/off state changes, LED will light on one second and then off. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Show dimmer state |
2 | Show night mode |
3 | One flash mode |
Whenever the AC power return from lost, PAD02 will restore the switch state which could be Dimmer offu3001Last dimmer stateu3001Dimmer on. The default setting is Last dimmer state. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Dimmer off |
1 | Last dimmer state |
2 | Dimmer on |
Dimensions | 0.0680000x0.0830000x0.0270000 mm |
Weight | 51 gr |
Hardware Platform | SD3502 |
EAN | 4713698574406 |
IP Class | IP 20 |
Voltage | 230V |
Load | 2A |
Device Type | Light Dimmer Socket |
Network Operation | Always On Slave |
Z-Wave Version | 6.51.09 |
Certification ID | ZC10-17045556 |
Z-Wave Product Id | 0x013C.0x0005.0x0031 |
Z-Wave Scene Type | Scene |
Color | White |
Firmware Updatable | Updatable by Consumer by RF |
Neutral Wire Required | ok |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |