This is a
Tripple Click the Temper Switch on the backside to confirm inclusion, exclusion and association.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
The Z-Wave 4 in 1 Sensor is designed with three detection sensors:
The Philio Multi Sensor is a Z-Wave door/ window sensor, motion sensor, lighting sensor and temperature sensor in one package. Thanks to this the PSM02 can be uses as a security device or home automation device, e.g. to send an alarm when a motion is detected, turn the light on/ off automatically at night or to adjust the heater.
The product consists of two elements - the detector and the magnet. The magnet is mounted on the moving part of the window or of the door. The other part is placed on the frame.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Tripple Click the Temper Switch on the device to enter inclusion mode. Within 1 second press the button again for 5 seconds.
The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Tripple Click the Temper Switch on the backside confirms inclusion and exclusion.
Tripple Click the Temper Switch on the backside confirms inclusion and exclusion.
The detector can be used as a security device or home automation device. When the detector is cooperated with security appliances, the (1) Door/window or (2) PIR sensor act as an alarm detector. Alternatively, when the detector is worked with Z-Wave controller, the detector can be set to perform the role of home automation device by detecting both changes in PIR motion detect or door/window open close signal with percentage of illumination lux levels.
One home automation scenario is, once night falls, the percentage of ambient illumination is lower than preset value. If a person moves within or across the devices field of vision, a trigger radio signal will be transmitted so as to turn connected lightings for better illumination.
Another scenario is to combine (1) Door/window (2) PIR (3) illumination sensors to recognize people is coming in or going out and turn the light on/off automatically.
The temperature sensor can detect the environment temperature so as to adjust heater or cooler to achieve preset temperature or detect the abnormal environment temperature (like freeze sensor or fire sensor) to send the warning message.
After powering up the divice needs several minutes to setup and work properly.
The device has a tamper switch, which starts alarm when the device is forcibly removed.
The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame. To issue a NIF execute the following action:
Tripple Click the Temper Switch on the backside sends out a Node Information Frame.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
2 | 7 | group 2 is for light control, the device will send the u201cBasic Setu201d command to this group. |
1 | 7 | group 1 is for receiving the report message, like triggered event, temperature, illumination etc. |
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Setting the BASIC command value to turn on the light Size: 1 Byte, Default Value: ff
Setting | Description |
---|---|
ff | 0xFF(-1) turns on the light. |
01 - 64 | For dimmers 1 to 100 means the light strength |
parameter to set the Sensitivity for the PIR (Passiv Infrared Sensor) Size: 1 Byte, Default Value: 46
Setting | Description |
---|---|
00 | 0 means disable the PIR motion; |
01 - 63 | 1 means the lowest sensitivity, 99 means the highest sensitivity |
Setting the illumination threshold to turn on the light. When the event triggered and the environment illumination lower then the threshold, the device will turn on the light Size: 1 Byte, Default Value: 63
Setting | Description |
---|---|
00 | 0 means turn off illumination detected function And never turn on the light. |
00 - 64 | 1 means darkest. 99 means brightest. 100 means turn off illumination detected function. And always turn on the light |
parameter to set the Operation Mode Size: 1 Byte, Default Value: 00
Setting | Description |
---|
parameter to set the sensor functions Size: 1 Byte, Default Value: 04
Setting | Description |
---|
In the security mode, after the PIR motion detected, setting the re-detect time Size: 1 Byte, Default Value: 03
Setting | Description |
---|
After turn on the light, setting the delay time to turn off the light when the PIR motion is not detected Size: 1 Byte, Default Value: 04
Setting | Description |
---|
interval time for auto report the battery level Size: 1 Byte, Default Value: 0c
Setting | Description |
---|
interval time for auto report the door/window state Size: 1 Byte, Default Value: 0c
Setting | Description |
---|
interval time for auto report the temperature Size: 1 Byte, Default Value: 0c
Setting | Description |
---|
interval time for auto report the temperature Size: 1 Byte, Default Value: 0c
Setting | Description |
---|
Dimensions | 0.0950000x0.0300000x0.0180000 mm |
Weight | 70 gr |
EAN | 4713698570040 |
Battery Type | 1 * CR123 |
Device Type | Routing Binary Sensor |
Generic Device Class | Binary Sensor |
Specific Device Class | Routing Binary Sensor |
Firmware Version | 01.00 |
Z-Wave Version | 03.41 |
Certification ID | ZC08-13050003 |
Z-Wave Product Id | 013c.0002.0002 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |