This is a
Tripple Click the Temper Switch on the backside to confirm inclusion, exclusion and association.
The Z-Wave 4 in 1 Sensor is designed with three detection sensors:
The Philio Multi Sensor is a Z-Wave door/ window sensor, motion sensor, lighting sensor and temperature sensor in one package. Thanks to this the PSM02 can be uses as a security device or home automation device, e.g. to send an alarm when a motion is detected, turn the light on/ off automatically at night or to adjust the heater.
The product consists of two elements - the detector and the magnet. The magnet is mounted on the moving part of the window or of the door. The other part is placed on the frame.
The detector can be used as a security device or home automation device. When the detector is cooperated with security appliances, the (1) Door/window or (2) PIR sensor act as an alarm detector. Alternatively, when the detector is worked with Z-Wave controller, the detector can be set to perform the role of home automation device by detecting both changes in PIR motion detect or door/window open close signal with percentage of illumination lux levels.
One home automation scenario is, once night falls, the percentage of ambient illumination is lower than preset value. If a person moves within or across the devices field of vision, a trigger radio signal will be transmitted so as to turn connected lightings for better illumination.
Another scenario is to combine (1) Door/window (2) PIR (3) illumination sensors to recognize people is coming in or going out and turn the light on/off automatically.
The temperature sensor can detect the environment temperature so as to adjust heater or cooler to achieve preset temperature or detect the abnormal environment temperature (like freeze sensor or fire sensor) to send the warning message.
After powering up the divice needs several minutes to setup and work properly.
The device has a tamper switch, which starts alarm when the device is forcibly removed.
Reset to factory default | Tripple Click the Temper Switch on the device to enter inclusion mode. Within 1 second press the button again for 5 seconds. |
Inclusion | Tripple Click the Temper Switch on the backside confirms inclusion and exclusion. |
Exclusion | Tripple Click the Temper Switch on the backside confirms inclusion and exclusion. |
NIF | Tripple Click the Temper Switch on the backside sends out a Node Information Frame. |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
2 | 7 | group 2 is for light control, the device will send the u201cBasic Setu201d command to this group. |
1 | 7 | group 1 is for receiving the report message, like triggered event, temperature, illumination etc. |
Setting the BASIC command value to turn on the light Size: 1 Byte, Default Value: ff
Setting | Description |
---|---|
ff | 0xFF(-1) turns on the light. |
01 - 64 | For dimmers 1 to 100 means the light strength |
parameter to set the Sensitivity for the PIR (Passiv Infrared Sensor) Size: 1 Byte, Default Value: 46
Setting | Description |
---|---|
00 | 0 means disable the PIR motion; |
01 - 63 | 1 means the lowest sensitivity, 99 means the highest sensitivity |
Setting the illumination threshold to turn on the light. When the event triggered and the environment illumination lower then the threshold, the device will turn on the light Size: 1 Byte, Default Value: 63
Setting | Description |
---|---|
00 | 0 means turn off illumination detected function And never turn on the light. |
00 - 64 | 1 means darkest. 99 means brightest. 100 means turn off illumination detected function. And always turn on the light |
parameter to set the Operation Mode Size: 1 Byte, Default Value: 00
Setting | Description |
---|
parameter to set the sensor functions Size: 1 Byte, Default Value: 04
Setting | Description |
---|
In the security mode, after the PIR motion detected, setting the re-detect time Size: 1 Byte, Default Value: 03
Setting | Description |
---|
After turn on the light, setting the delay time to turn off the light when the PIR motion is not detected Size: 1 Byte, Default Value: 04
Setting | Description |
---|
interval time for auto report the battery level Size: 1 Byte, Default Value: 0c
Setting | Description |
---|
interval time for auto report the door/window state Size: 1 Byte, Default Value: 0c
Setting | Description |
---|
interval time for auto report the temperature Size: 1 Byte, Default Value: 0c
Setting | Description |
---|
interval time for auto report the temperature Size: 1 Byte, Default Value: 0c
Setting | Description |
---|
Dimensions | 0.0950000x0.0300000x0.0180000 mm |
Weight | 70 gr |
EAN | 4713698570040 |
Battery Type | 1 * CR123 |
Device Type | Routing Binary Sensor |
Generic Device Class | Binary Sensor |
Specific Device Class | Routing Binary Sensor |
Firmware Version | 01.00 |
Z-Wave Version | 03.41 |
Certification ID | ZC08-13050003 |
Z-Wave Product Id | 013c.0002.0002 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |