Quickstart

This is a Routing Binary Sensor for XXXQFrequencyName. To run this device please insert fresh 1 * CR123 batteries. To run this device please make sure the internal battery is fully charged.

Tripple Click the Temper Switch on the backside to confirm inclusion, exclusion and association.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The Z-Wave 3 in 1 sensor is designed with three detection sensors:

  • PIR/Motion
  • Temperature
  • Illumination

The detector can be used as a security device or home automation device. When the detector is cooperated with security appliances, the detector is acting as a security device by detecting changes in infra-red radiation levels. If a person moves within or across the devices field of vision, a trigger radio signal will be transmitted to cause full alarm condition in order to frighten intruders away. Alternatively, when the detector is worked with Z-Wave Controller, the detector can be set to perform the role of home automation device by detecting both changes in infra-red radiation levels and percentage of lux levels. Once night falls, the percentage of ambient illumination is lower than preset value. If a person moves within or across the devices field of vision, a trigger radio signal will be transmitted so as to turn connected lightings for better illumination. Every time when PIR trig, the sensor will also send temperature and illumination value as well. Also the temperature will send out the value when temperature changes.

Installation

  • Open the casing and dissemble the front part of the case.
  • Put the included CR123A battery into the battery compartment and close the casing.
  • Mount the device with the included screws or the adhesive tape at a wall at about 2 m above surface. To enhance operation place the device on a position which can detect the room widely.

Product Usage

The motion detector sends a Z-Wave signal to associated devices when a motion is detetced. After powering up the divice needs several minutes to setup and work properly.

The device has a tamper switch, which starts alarm when the device is forcibly removed.

Reset to factory default

Tripple Click the Temper Switch on the device to enter inclusion mode. Within 1 second press the button again for 5 seconds.

Inclusion

Tripple Click the Temper Switch on the backside confirms inclusion and exclusion.

Exclusion

Tripple Click the Temper Switch on the backside confirms inclusion and exclusion.

NIF

Tripple Click the Temper Switch on the backside sends out a Node Information Frame.

Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
2 7 group 2 is for light control, the device will send the u201cBasic Setu201d command to this group.
1 7 group 1 is for receiving the report message, like triggered event, temperature, illumination etc.

Configuration Parameters

Parameter 2: Basic Set Level

Setting the BASIC command value to turn on the light
Size: 1 Byte, Default Value: ff

Setting Description
ff 0xFF(-1) turns on the light.
01 - 64 For dimmers 1 to 100 means the light strength

Parameter 3: PIR Sensitivity

parameter to set the Sensitivity for the PIR (Passiv Infrared Sensor)
Size: 1 Byte, Default Value: 46

Setting Description
00 0 means disable the PIR motion;
01 - 63 1 means the lowest sensitivity, 99 means the highest sensitivity

Parameter 4: Light Threshold

Setting the illumination threshold to turn on the light. When the event triggered and the environment illumination lower then the threshold, the device will turn on the light
Size: 1 Byte, Default Value: 63

Setting Description
00 0 means turn off illumination detected function And never turn on the light.
01 - 64 1 means darkest. 99 means brightest. 100 means turn off illumination detected function. And always turn on the light

Parameter 5: Operation Mode

parameter to set the Operation Mode
Size: 1 Byte, Default Value: 00

Setting Description

Parameter 6: Multi-Sensor Function Switch

parameter to set the sensor functions
Size: 1 Byte, Default Value: 04

Setting Description

Parameter 8: PIR Re-Detect Interval Time

In the security mode, after the PIR motion detected, setting the re-detect time
Size: 1 Byte, Default Value: 03

Setting Description

Parameter 9: Turn Off Light Time

After turn on the light, setting the delay time to turn off the light when the PIR motion is not detected
Size: 1 Byte, Default Value: 04

Setting Description

Parameter 10: Auto Report Battery Time

interval time for auto report the battery level
Size: 1 Byte, Default Value: 0c

Setting Description

Parameter 12: Auto Report Illumination Time

interval time for auto report the illumination
Size: 1 Byte, Default Value: 0c

Setting Description

Parameter 13: Auto Report Temperature Time

interval time for auto report the temperature
Size: 1 Byte, Default Value: 0c

Setting Description

Technical Data

Dimensions 0.0280000x0.0960000x0.0230000 mm
Weight 39 gr
Hardware Platform ZM3102
EAN 4713698570057
Battery Type 1 * CR123
Device Type Routing Binary Sensor
Generic Device Class Binary Sensor
Specific Device Class Routing Binary Sensor
Firmware Version 01.00
Z-Wave Version 03.29
Certification ID ZC08-13050003
Z-Wave Product Id 013c.0002.0002
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeRouting Binary Sensor