This is a
The Philio 3 in 1 Sensor is designed with three detection sensors: PIR/Motion, temperature, illumination. The detector can be used as a security device or home automation device. When the detector is cooperated with security appliances, the detector is acting as a security device by detecting changes in infra-red radiation levels. If a person moves within or across the devices field of vision, a trigger radio signal will be transmitted to cause full alarm condition in order to frighten intruders away. Once night falls, the percentage of ambient illumination is lower than preset value. If a person moves within or across the devices field of vision, a trigger radio signal will be transmitted so as to turn connected lightings for better illumination. Every time when PIR trig, the sensor will also send temperature and illumination value as well. Also the temperature will send out the value when temperature changes. Note: The illumination sensor does not work with Fibaro Homecenter 2 and Zipabox yet.
When included securely the device is able to accept secure commands and to send secure commands to other devices. The commands and the receiver of the commands sent out on single click and on double click of the rocker can be defined in configuration parameters and association groups.
Download high resolution images for Philio products.
Reset to factory default |
|
Inclusion |
|
Exclusion |
|
NIF | Press any key once, the device will awake 10 seconds. |
Wakeup | Press any key once, the device will awake 10 seconds. |
Protection | XXXProtection |
FirmwareUpdate | The device support the Z-Wave firmware update via OTA. Before starting the procedure, please remove the front cover of the device. Otherwise the hardware check will be failed. Let the controller into the firmware update mode, and then press the front tamper key once to start the update. After finish the firmware download, the LED will start flash in every 0.5 second. At that time, please don"t remove the battery, otherwise it will cause the firmware broken, and the device will no function. After the LED stop flash, it is recommended that the user power up the device. Caution: After remove the battery, please wait about 30
seconds, and then re-install the battery. |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 8 | Receiving the report message, like triggered event, temperature, illumination etc. |
2 | 8 | Light control, the device will send the “Basic Set” command |
Setting the BASIC command value to turn on the light Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 | turn off the light |
1 - 100 | the light strength. |
254 | turn on the light. |
PIR sensitivity settings. Size: 1 Byte, Default Value: 80
Setting | Description |
---|---|
0 | disable the PIR motion. |
1 - 99 | 1 means the lowest sensitivity, 99 means the highest sensitivity. High sensitivity means can detected long distance, but if there is more noise signal in the environment, it will re-trigger too frequency. |
Setting the illumination threshold to turn on the light. When the event triggered and the environment illumination lower then the threshold, the device will turn on the light. 0 means turn off illumination detected function. And never turn on the light.
Notice: In none test mode, only the value in 1 to 99 will enable the illumination detected function and update the illumination value.
Size: 1 Byte, Default Value: 99
Setting | Description |
---|---|
0 | turn off illumination detected function. |
1 - 100 | 1 means darkest. 99 means brightest. 100 means turn off illumination detected function. And always turn on the light. |
Operation mode. Using bit to control. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Reserve. |
2 | 1 means test mode, 0 means normal mode. Notice: This bit only effect by the DIP Switch setting to “customer mode”, otherwise it decides by DIP Switch setting to Test or Normal Mode |
4 | Reserve. |
8 | Setting the temperature scale. 0: Fahrenheit, 1:Celsius |
16 | Disable the illumination report after event triggered. (1:Disable, 0:Enable) |
32 | Disable the temperature report after event triggered. (1:Disable, 0:Enable) |
64 | Reserve. |
128 | Disable the back key release into test mode. (1:Disable, 0:Enable) |
Multisensor function switch. Using bit to control. Size: 1 Byte, Default Value: 4
Setting | Description |
---|---|
1 | Reserve. |
2 | Disable PIR integrate Illumination to turn ON the lighting nodes in the association group 2. (1:Disable, 0:Enable) |
4 | Reserve. |
8 | Reserve. |
16 | Reserve. |
32 | Reserve. |
64 | Reserve. |
128 | Reserve. |
Customer function switch, using bit control. Size: 1 Byte, Default Value: 4
Setting | Description |
---|---|
1 | Reserve. |
2 | Enable sending motion OFF report. (0:Disable, 1:Enable) |
4 | Enable PIR super sensitivity mode. (0:Disable, 1:Enable) |
8 | Reserve. |
16 | Notification Type, 0: Using Notification Report. 1: Using Sensor Binary Report. |
32 | Disable Multi CC in auto report. (1:Disable, 0:Enable) |
64 | Disable to report battery state when the device triggered. (1:Disable, 0:Enable) |
128 | Reserve. |
In the normal mode, after the PIR motion detected, setting the re-detect time. 8 seconds per tick, default tick is 3 (24 seconds).Setting the suitable value to prevent received the trigger signal too frequently. Also can save the battery energy.Notice: If this value bigger than the configuration setting NO. 9. There is a period after the light turned off and the PIR not start detecting. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 127 | PIR Re-Detect Interval Time |
After turn on the lighting, setting the delay time to turn off the lighting when the PIR motion is not detected. 8 seconds per tick, default tick is 4 (32 seconds).0 means never send turn off light command. Size: 1 Byte, Default Value: 4
Setting | Description |
---|---|
0 - 127 | Turn Off Light Time |
The interval time for auto report the battery level. 0 means turn off auto report battery.The default value is 12. The tick time can setting by the configuration No.20. Size: 1 Byte, Default Value: 12
Setting | Description |
---|---|
0 - 127 | Auto Report Battery Time |
The interval time for auto report the illumination. 0 means turn off auto report illumination.The default value is 12. The tick time can setting by the configuration No.20. Size: 1 Byte, Default Value: 12
Setting | Description |
---|---|
0 - 127 | Auto Report Illumination Time |
The interval time for auto report the temperature. 0 means turn off auto report temperature.The default value is 12. The tick time can setting by the configuration No.20. Size: 1 Byte, Default Value: 12
Setting | Description |
---|---|
0 - 127 | Auto Report Temperature Time |
The interval time for auto report each tick. Setting this configuration will effect configuration No.10, No.11, No.12 and No.13.Caution: Setting to 0 means turn off all auto report function. Size: 1 Byte, Default Value: 30
Setting | Description |
---|---|
0 - 255 | Auto Report Tick Interval |
The temperature differential to report.0 means turn off this function. The unit is Fahrenheit.Enable this function the device will detect every minutes. And when the temperature is over 140 degree Fahrenheit, it will continue report.Enable this functionality will cause some issue please see the detail in the u201cTemperature Reportu201d section. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 - 127 | Temperature Differential Report |
The illumination differential to report.0 means turn off this function. The unit is percentage.Enable this function the device will detect every minutes. Enable this functionality will cause some issue please see the detail in the Illumination Report section. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 99 | Illumination Differential Report |
Dimensions | 95x28x35 mm |
Weight | 48 gr |
Hardware Platform | ZM5202 |
EAN | 4713698570170 |
IP Class | IP 20 |
Battery Type | 1 * CR123A |
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Z-Wave Version | 6.51.02 |
Certification ID | ZC10-14080017 |
Z-Wave Product Id | 0x013C.0x0002.0x000D |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |