This is a
To confirm Inclusion and Exclusion press and hold the User Button on the door lock until it beeps twice.
The ZEC 100 Danalock is a smart lock from Poly Control to upgrade your existing door lock. You will need no more key to lock or unlock your door. With the Danalock you can control your door lock with a Z-Wave Controller or via Z-Wave Gateway with your Smartphone. From insde the room you can operate the lock by touching the user button.
Within the scope of delivery you will get a Danalock cylinder to replace the existing cylinder of your door lock. You will also get the main device with the battery and the assisted motor and a screwdriver for mounting. The cylinder is applied for european doors.
Scope of Delivery:
The ZEC 100 smart lock is for indoor use only. It is installed at the inner side of the door and replaces the normal lock cylinder.
To open the door from outside you can use an associated Z-Wave controller or a smartphone together with a Z-Wave IP-Gateway. In addition you can open the lock conventionally with the normal keys.
From inside you can open the lock via Z-Wave or by touching the User Button.
The color of the LED Grid shows the lock status: Green for opened, Red for locked.
Reset to factory default | To reset the device press and hold the User Button on the door lock until it beeps ten times. |
Inclusion | To confirm Inclusion and Exclusion press and hold the User Button on the door lock until it beeps twice. |
Exclusion | To confirm Inclusion and Exclusion press and hold the User Button on the door lock until it beeps twice. |
NIF | To issue a Node Information Frame press and hold the User Button on the door lock until it beeps twice. |
Wakeup | To wake up the device manually press and hold the User Button on the door lock until it beeps twice. |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | To confirm Association press and hold the User Button on the door lock until it beeps twice. |
parameter defines which direction the motor turns the lock in relation to the latch Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Clockwise when latching |
01 | Counterclockwise when latching |
parameter defines whether the motor goes slower (more torque) or faster (less torque) when turning the lock Size: 1 Byte, Default Value: 03
Setting | Description |
---|---|
01 | Slowest Speed, Strongest Torque |
02 | Slow Speed, Stronger Torque |
03 | Normal Speed,Normal Torque |
04 | Fast Speed, Weak Torque |
05 | Fastest Speed, Weakest Torque |
parameter defines if more or less torque is used at latch/unlatch operations (less torque safes power) Size: 1 Byte, Default Value: 01
Setting | Description |
---|---|
00 | Less torque, Power Saving mode |
01 | Normal Mode |
parameter defines how many degrees the lock turns at latch/unlatch operations Size: 1 Byte, Default Value: 09
Setting | Description |
---|
parameter defines amount of seconds after opening the door automatically locks again Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Disabled |
01 - 3c | delay after opening in seconds |
parameter defines if an acoustic signal confirms latch/unlatch operations Size: 1 Byte, Default Value: 01
Setting | Description |
---|---|
00 | Latch/unlatch Sound disabled |
01 | Latch/unlatch Sound enabled |
parameter defines the battery type (voltage) is used to power the device value shouldnt be changed! Size: 1 Byte, Default Value: 01
Setting | Description |
---|---|
00 | 3.6 volt battery type |
01 | 3.0 volt battery type |
parameter defines the percent battery status threshold underrun which leads to an acoustic signal after latch/unlatch operations Size: 1 Byte, Default Value: 1e
Setting | Description |
---|
Dimensions | 0.0800000x0.0800000x0.0500000 mm |
Weight | 385 gr |
EAN | 5712560101039 |
Battery Type | 4 * CR123 |
Firmware Version | 02.04 |
Z-Wave Version | 02.4e |
Z-Wave Product Id | 010e.0003.0002 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |