Popp
Smart Outdoor Plug
SKU: POPE700397
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Switching is controlled by the local button or wirelessly. The use of the local button and the behavior on wireless commands can be configured using configuration parameters. When detached from the control of local leads the button on the device can be used to trigger scenes in a central gateway. A single click and double click are distinguished.
The device is also measuring the mains voltage supply reporting mains voltage and mains frequency. Additionally, the power consumption of the attached load is monitored as well.
All metering values can be requested from the central controller and will be reported unsolicited if configured.
Installation
The device can be plugged into every standard power outlet Type F. Thanks to IP44 rating this device can be used in wet environments such as bathrooms or basements and even outdoor. Do not stack the device!
Product Usage
The device is able to switch electric loads up to 3500 W and can be switched wirelessly or using the local button. The connected load is measured and reported. Trigger values can define unsolicited power reports. The device includes a virtual circuit breaker. The configuration values 26-28 define the behavior of this function. Depending on the configuration parameter 4 the local button with either control the local load or sends scene activation commands to the central gateway.
| Reset to factory default | Push and hold the button for 10seconds. After 5 seconds the LED on the button will blink fast. |
| Inclusion | 1. Plug the device into the power outlet.
2. Press the button three times in succession.
|
| Exclusion | 1. plug the device into the power outlet.
2. Press the button three times in succession. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | Single Click the button to confirm the update |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifeline |
| 2 | 5 | Control other devices on single click of the button. BASIC command (on/off) is sent according to switching state of the load. |
Configuration Parameters
Parameter 1: LED Operation Mode
Defines when the LED shall shine and how Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | LED off, only blinks on traffic |
| 1 | Defined by Parameter 21 and 22 |
Parameter 2: Auto Off
Defines if and after which time the device shall turn off without any user interaction Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | no auto off |
| 1 - 65535 | seconds |
Parameter 3: Switching behavior when receiving wireless OFF
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Switches off |
| 1 | Ignores Off command |
| 2 | Switches on |
| 3 | Switches on, when receiving off command and current state is off |
Parameter 4: Button Mode
This parameter defines if the local button shall control (switch) the load or it is only used to send out scene control commands to the central controller. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Controls Load + Controls Scenes |
| 1 | Scene Control Only |
Parameter 5: Status after Power Failure
Defines the switching status after a power failure or unplugging Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Always off |
| 1 | Return to last switching state |
Parameter 21: LED Color on OFF state
Defines the behavior of the LED when the load is switched off Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Off |
| 1 | Red |
| 2 | Green |
Parameter 22: LED Color on ON state
Defines the behavior of the LED when the load is switched on Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | Off |
| 1 | Red |
| 2 | Green |
Parameter 23: Voltage Report Threshold
Report the voltage when the voltage has changed by more then X * 1 V. When disabled the device will report every 10 minutes regardless of current voltage. Size: 1 Byte, Default Value: 100
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 - 250 | Volt |
Parameter 24: Current Reporting Threshold
Report the current when the current has changed by more then X *0,01 A. When disabled the device will report every 10 minutes regardless of current change. Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 - 255 | * 0,01 A |
Parameter 25: Power Reporting Threshold
Report the power when the power has changed by more then X Watt. When disabled the device will report every 10 minutes regardless of power consumption change. Size: 1 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 - 255 | W |
Parameter 26: Soft Circuit Breaker Threshold
When the power draw exceeds the value set in this parameter for a time set in parameter 28 the soft ciruit breaker will disconnect the load. Size: 2 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 - 3600 | W |
Parameter 27: Soft Circuit Breaker Recovery Time
Once the soft circuit breaker tipps and the load is disconnected the load will be automatically reconneced after X seconds. When disabled the load must be repowered manually or with wireless command. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Never |
| 1 - 255 | sec. |
Parameter 28: Soft Circuit Breaker Delay Time
This delay time defines how fast the soft circuit breaker wil react when the threshold power is exceeded. The power is cut off only if the power draw remains over the threshold level for the defines time. Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 255 | * 0,1 sec |
Technical Data
| Dimensions | 114x59x92 mm mm |
| Weight | 153 gr |
| Hardware Platform | ZM5101 |
| EAN | 4251295700397 |
| IP Class | IP IP44 |
| Voltage | 230V |
| Load | 3500 W |
| Device Type | On/Off Power Switch |
| Generic Device Class | Binary Switch |
| Specific Device Class | Binary Power Switch |
| Firmware Version | 03.01 |
| Z-Wave Version | 6.01 |
| Certification ID | ZC10-18026015 |
| Z-Wave Product Id | 0x0154.0x0003.0x000a |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |