Philio
Smoke Sensor
SKU: PSG01
Quickstart
This is a
1. Have Z-Wave Controller entered inclusion mode.2. Pressing button three times within 1.5 seconds to enter the inclusion mode.3. After add successful, the device will wake to receive the setting command from Z-Wave Controller about 20 seconds.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
TheSmokeSensor PSG01 is designed to give early warning of developing fires by giving off the alarm sounds from its build-in alarm horn, based on Z-Wavetechnology.It is a Z-Wave plus product, it supports the security, OTA... Those newest features of theZ-Wavetechnology.Z-Wave is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and light commercial environments. The technology uses a low-power RF radio embedded or retrofitted into home electronics devices and systems, such as lighting, home access control, entertainment systems and household appliances.
| Reset to factory default | Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.1. Pressing button four times within 1.5 seconds and do not release the button in the 4 thpressed, and the red LED will light ON.2. After the red LED flash 9 times, release the button within 2 seconds.3. IDs are removed and all settings will reset to factory default. |
| Inclusion | 1. Have Z-Wave Controller entered inclusion mode.2. Pressing button three times within 1.5 seconds to enter the inclusion mode.3. After add successful, the device will wake to receive the setting command from Z-Wave Controller about 20 seconds. |
| Exclusion | 1. Have Z-WaveController entered exclusion mode.2. Pressing button three times within 1.5 seconds toenter the exclusion mode. Node ID has been removed. |
| NIF | XXXNIF |
| Wakeup | After the device adding to the network, it will wake-up once per day in default. When it wake-up it will broadcast the Wake Up Notification messagetothenetwork,andwake-up10secondsforreceivethe setting commands. The wake-up interval minimum setting is 30 minutes, and maximum setting is 120 hours. And the interval step is 30 minutes. If the user want to wake-up the device immediately, please press the button once. The device will wake-up 10 seconds. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 10: Auto Report Battery Time
The interval time for auto report the battery level. 0 means turn off auto report battery. The default value is 12.The value is in minutes. Size: 1 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 0 - 127 | The interval time for auto report thebattery level. |
Parameter 7: Customer Function
Customer function switch, using bit control.Bit4: Notification Type,0: Using Notification Report. 1: Using Sensor Binary Report. Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 16 | Notification Type, Using Sensor Binary Report. |
| 0 | Notification Type, Using Notification Report. |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | 01 |
| Z-Wave Version | 6.51.02 |
| Certification ID | ZC10-14110003 |
| Z-Wave Product Id | 0x013C.0x0002.0x001E |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |