This is a
For Inclusion of Z-Wave devices into the remote controls network do the following steps: Press and hold the left + right arrow keys simultaneously for 3 seconds and select "Add Device". For including the ZRC-100 as a secondary controller into an existing the Z-Wave network do the following steps: Bring your primary controller into inclusion mode. Press and hold the up + down arrow keys simultaneously for 3 seconds and select "Learning Mode" on the ZRC-100.
This is a universal remote control with extended Z-Wave capability. The device is able to control its own Z-Wave network and works well together with IP Gateway controlling scene activation. It can control up to 12 Z-wave scenes and supports multi-channel devices e.g. door lock, window shades, thermostat, z-wave-IR extender, dimmer, switch, etc.
Remove the battery cover on the back of your remote. Insert the 4 x AAA batteries to the battery compartment according to the marks. Refit the battery cover.
The ZRC100 Remote Control has a LCD screen which showes the easy-to-use menu. The menu is controlled with arrow keys and, an OK and an BACK button. The 3 short cut keys are fully customizable and give quick access to scenes and devices.
Reset to factory default | For reseting the ZRC-100 do the following steps: Press and hold the LEFT + RIGHT arrow keys simultaneously for 3 seconds, select "Advanced Setup", select "Reset to Default", confirm the reset with the right arrow key. Note: After reset the remote, each device should individually perform in the section on "Delete device from the network" and "Add device to the network". |
Inclusion | For including the ZRC-100 as a secondary controller into an existing the Z-Wave network do the following steps: Bring your primary controller into inclusion mode. Press and hold the UP + DOWN arrow keys simultaneously for 3 seconds and select "Learning Mode" on the ZRC-100 to include or exclude it. |
Exclusion | For including the ZRC-100 as a secondary controller into an existing the Z-Wave network do the following steps: Bring your primary controller into inclusion mode. Press and hold the UP + DOWN arrow keys simultaneously for 3 seconds and select "Learning Mode" on the ZRC-100 to include or exclude it. |
NIF | Press and hold the left + right arrow keys simultaneously for 3 seconds for sending a node information frame. |
Wakeup | The device can be woken up manually by pressing any button. |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | When a device is included it will be added automatically to a group in the ZRC-100. |
Group Number | Maximum Nodes | Description |
---|---|---|
12 | 32 | |
11 | 32 | |
10 | 32 | |
9 | 0 | |
8 | 0 | |
7 | 0 | |
6 | 32 | |
5 | 0 | |
4 | 0 | |
3 | 0 | |
2 | 0 | |
1 | 32 |
As long as this device is not included into a Z-Wave network of a different controller it is able to manage its own Z-Wave network as primary controller. As a primary controller the device can include and exclude other devices in its own network, manage associations, and reorganize the network in case of problems. The following controller functions are supported:
Communication between two Z-Wave devices only works if both belong to the same wireless network. Joining a network is called inclusion and is initiated by a controller. The controller needs to be turned into the inclusion mode. Once in this inclusion mode the other device needs to confirm the inclusion - typically by pressing a button.
If current primary controller in your network is in special SIS mode this and any other secondary controller can also include and exclude devices.
To become primary a contoller have to be resetted and then include a device.
For Inclusion of Z-Wave devices into the remote controls network do the following steps: Press and hold the left + right arrow keys simultaneously for 3 seconds and select "Add Device". Press the dedicated button on the target device to include it.
The primary controller can exclude devices from the Z-Wave network. During exclusion the relationship between the device and the network of this controller is terminated. No communication between the device and other devices still in the network can happen after a successful exclusion. The controller needs to be turned into the exclusion mode. Once in this exclusion mode the other device needs to confirm the exclusion - typically by pressing a button.
Attention: Removing a device from the network means that it is turned back into factory default status. This process can also exclude devices from it's previous network.
For Exclusion of Z-Wave devices from the remote controls network do the following steps: Press and hold the left + right arrow keys simultaneously for 3 seconds and select "Delete Device". Press the dedicated button on the target device to exclude it.
The device can hand over its primary role to another controller and become secondary controller.
There is also the posibilty to make your ZRC-100 to a primary controller.
Replicating All Network and Device Information from a Primary Controller to your ZRC-100:
Dimensions | 0.0520000x0.1620000x0.0150000 mm |
Weight | 80 gr |
Device Type | Remote Control - Simple |
Generic Device Class | Portable Controller |
Specific Device Class | Portable Scene Controller |
Firmware Version | 01.02 |
Z-Wave Version | 03.22 |
Certification ID | ZC08-16010003 |
Z-Wave Product Id | 5254.0001.8380 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |