This is a
Single click on the large middle button (PROG) confirms inclusion and exclusion. Depending on power supply (battery or 5 V external) the device will we always active or run in a pseudo active mode (FLIRS) preserving battery power. To switch between FLIRS and Active mode press and hold the the PROG button for 4 seconds - the LED will stay off. Now release the PROG switch and press it 3 times within 2 seconds. The LED will either flash two times (indicates FLIRS) or four times (indicates active mode).
This device is a 100% interoperable Z-Wave to IR extender to control Air Conditions. It transmits IR control code with a wide range including the temperature and supports Z-Wave compliant Home Gateways and portable Controllers. It also has an integrated 5-direction IR emitter hemispherical coverage, a programmable power level (high or low) for external IR emitter to aviod saturation of IR receivers. The device is also with built?in temperature sensor which allows gateway or controller to get the current room temperature.
Mounting Locations
Mounting Process
The ZXT-120 can be mounted to a wall or wooden racks using the two key holes in the bottom case.
The Built in IR code library supports most of the popular air conditioner brands in the market. Z?Wave gateway and controller does not need to have any IR control code knowledge. User can use ZWave controller or gateway to select the IR code according to the ZXT-120 code list separately provided through Z-Wave configuration command.
A complete list of all supported AC devices can be downloaded from the manufacturers homepage http://www.remotec.com.hk/zaspx/support.aspx
Infrared Code Learning
In case none of the code on the code list works for the targeted air conditioner, user can use IR code learning function using configuration according to below steps:
Reset of the Device
Press and hold (PROG) button for 10seconds on ZXT-120. The LED will flash twice until reset process is completed.
Reset to factory default | XXXResetDescription |
Inclusion | Single click on the large middle button (PROG) confirms inclusion and exclusion. |
Exclusion | Single click on the large middle button (PROG) confirms inclusion and exclusion. |
NIF | Single click on the large middle button (PROG) sends a Node Information Frame. |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
In case none of the code on the code list works for the targeted air conditioner, user can use IR code learning function. See manual at section IR Code Learning for a description of the procedure. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | OFF |
1 | ON (resume) |
02 - 11 | 19°C cool - 28°C cool |
12 - 21 | 19°C heat - 28°C heat |
22 | Dry mode |
Note: The status value 0x01 and 0x04 will be reset to 0 when the ZXT-120 receive a get command to this parameter Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Idle - this IR channel is idle |
01 | OK - the latest learning process successful and completed |
02 | Learning - the ZXT-120 is busy processing previous learning request |
04 | Failed - the latest learning request failed |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 255 | Code |
Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 | normal power mode |
255 | high power mode |
To avoid the IR interference by disabling the surrounding IR emitter if 2 air-conditioners in a room are used. Extend the battery life by disabling the Surround IR Emitters Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 | disable Surround IR Emitters |
255 | enable Surround IR Emitters |
Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | SWING OFF |
1 | SWING AUTO |
Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1 - 23 | Learn location |
Dimensions | 0.0362500x0.0208000x0.0875000 mm |
Weight | 57 gr |
Hardware Platform | ZM3102 |
EAN | 4896628183777 |
Battery Type | 4 * AAA |
Firmware Version | 01.01 |
Z-Wave Version | 03.2a |
Certification ID | ZC08-12090012 |
Z-Wave Product Id | 5254.0101.8377 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |