Secure
Temperature Sensor
SKU: SEC_SES301
Quickstart
This is a
Pushing the Button near the battery for two seconds confirms inclusion and exclusion. The same process issues a Node Information Frame and wakes up the device.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The SEC_SES301 is a battery operated device which acts as temperature sensor. It uses Z-Wave wireless commands to send its temperature data to a controller. The device is IP 30 rated and can therefore be used in dry environments only. The precision of the temperature sensor is +/- 0.5 degree.
Features include
- Can be configured to report on change in temperature or at set intervals
- The value of change that trigger reports is configurable in 0.1?C steps from 0.1?C to 10?C
- Temperature and battery level alarms can be sent to up to 4 separate devices
- Temperature reports can be configured to be in either Celsius or Fahrenheit
Installation
Choose the position where the unit is to be mounted. Avoid locations alongside or behind large metal surfaces that could interfere with the low-power radio signals between the unit and the Controller.
The SES301 should be mounted on an internal wall, around 1.5 m above floor level and in a position away from draughts, direct heat and sunlight.
Make sure that there will be sufficient space around the unit to allow easy access to the two retaining screws on the base of the wall plate.
Product Usage
The temperature sensor (communication pattern 3) can be used without further installation and configuration work.
| Reset to factory default | XXXResetDescription |
| Inclusion | Pushing the Button near the battery for two seconds confirms inclusion and exclusion. |
| Exclusion | Pushing the Button near the battery for two seconds confirms inclusion and exclusion. |
| NIF | Pushing the Button near the battery for two seconds issues a Node Information Frame. |
| Wakeup | Pushing the Button near the battery for two seconds wakes up the device. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 2 | 4 | Nodes to receive unsolicited low battery warnings report |
| 1 | 4 | Nodes to receive unsolicited multilevel sensor report |
Configuration Parameters
Parameter 1: Temperature Scale
Adjust the temperature scale Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 - 7f | Celsius |
| 80 - ff | Fahrenheit |
| 00 | Default |
Parameter 2: Delta Temperature
Set degree steps Size: 1 Byte, Default Value: 0a
| Setting | Description |
|---|---|
| 01 - 64 | * 0,1 K |
| 0a | default is 10 (steps of 1,0Cu00b0) |
Technical Data
| Dimensions | 0.0850000x0.0850000x0.0350000 mm |
| Weight | 140 gr |
| Hardware Platform | ZM3102 |
| EAN | 5015914840067 |
| Battery Type | 2 * AA |
| Device Type | Routing Multilevel Sensor |
| Generic Device Class | Multilevel Sensor |
| Specific Device Class | Routing Multilevel Sensor |
| Firmware Version | 00.04 |
| Z-Wave Version | 03.14 |
| Certification ID | ZC08-12060008 |
| Z-Wave Product Id | 0059.000d.0001 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |