Sensative

Strips Multi Sensor Comfort

SKU: SENECOMFORT

ZWave+

Quickstart

This is a Notification Sensor for XXXQFrequencyName. To run this device please insert fresh 1 * Lithium batteries. To run this device please make sure the internal battery is fully charged. To add this device to your network execute the following action:

Move the magnet to the rounded edge, and once the LED blinks, move the magnet away



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Your Strips Comfort is a Z-Wave multi-sensor that can be added to any certified Z-Wave system and operate with any Z-Wave device. Strips Comfort is a discreet temperature and light sensor.
Strips Comfort has a range up to 40 meters. The range can be extended by using any non-battery Z-wave device, which automatically acts as a repeater when placed between Strips Comfort and the controller.

Product Usage

Please note that poor network reliability will affect Strips Comfort´s battery life. When Strips Comfort blinks 5 times, this indicates that Strips Comfort failed to communicate with the controller. If it happens frequently you may move the controller closer or add an extender between the controller and Strips Comfort.



LED LIGHT SIGNALS

1 short blink: User commands (Table C) or alarm event feedback - when Strips is added.
2 short blink: User commands (Table C) - when Strips is not added.
1 long blink: Acknowledges first a completed user command and then the successful transmission of it.
5 or 10 short blink: Error (E.g. communication with controller failed)
Reset to factory default
Move the magnet to the rounded edge, and once the LED blinks, move the magnet away, on the 3rd repetition, leave the magnet as shown in the figure below (20mm from the rounded edge) for 10 seconds.
Inclusion
Move the magnet to the rounded edge, and once the LED blinks, move the magnet away
Exclusion
Move the magnet to the rounded edge, and once the LED blinks, move the magnet away (See figure below)
NIF XXXNIF
Wakeup
Wake up Strips manually for Z-Wave communication. Move the magnet to the rounded edge, and once the LED blinks, move the magnet away (See figure below). Repeat two more times within 10 seconds. A successful wake-up is confirmed with one LED blink.
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Z-Wave Plus Lifeline

Configuration Parameters

Parameter 2: LED alarm event reporting


Size: 1 Byte, Default Value: 1

Setting Description
0 Off
1 On

Parameter 3: Temperature & Light reporting frequency


Size: 1 Byte, Default Value: 1

Setting Description
1 Normal
2 Frequent

Parameter 4: Temperature reporting

(Does not affect temperature alarms)
Size: 1 Byte, Default Value: 1

Setting Description
0 Off
1 On

Parameter 5: Temperature reporting unit


Size: 1 Byte, Default Value: 0

Setting Description
0 Celsius
1 Fahrenheit

Parameter 6: Temperature alarms


Size: 1 Byte, Default Value: 0

Setting Description
0 Off
1 On

Parameter 7: High temperature alarm level


Size: 1 Byte, Default Value: 60

Setting Description
0 - 60 Value in °C (0 - 60°C)
236 - 255 Value in °C (-20 - -1)

Parameter 8: Low temperature alarm level


Size: 1 Byte, Default Value: 236

Setting Description
0 - 60 Value in °C (0 - 60°C)
236 - 255 Value in °C (-20 - -1)

Parameter 9: Ambient light reporting


Size: 1 Byte, Default Value: 1

Setting Description
0 Off
1 On
2 Report only when levels defined in parameter 10 & 11 are passed.

Parameter 10: High ambient light report level


Size: 4 Byte, Default Value: 40000

Setting Description
3 - 64 000 Value in LUX

Parameter 11: Low ambient light report level

(Must be significantly lower than parameter 10)
Size: 4 Byte, Default Value: 5000

Setting Description
1 - 42000 Value in LUX

Technical Data

Dimensions 15 x 195 x 6 mm
Weight 10 gr
Hardware Platform ZM5101
EAN 7350088520086
IP Class IP 65
Battery Type 1 * Lithium
Device Type Notification Sensor
Network Operation Reporting Sleeping Slave
Z-Wave Version 6.51.06
Certification ID ZC10-18015953
Z-Wave Product Id 0x019A.0x0003.0x0003
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeNotification Sensor